Difference between revisions of "TUFLOW Message 0045"

From Tuflow
Jump to navigation Jump to search
 
(5 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
{{TUFLOW_Message
 
{{TUFLOW_Message
|tuflow_message=ERROR 0045 (Map Output Interval not specified)<br>
+
|tuflow_message=ERROR 0045 - Map Output Interval is not specified.<br>
 
|alt_msg=NA
 
|alt_msg=NA
 
|type=[[ERROR]]<br>
 
|type=[[ERROR]]<br>
|message_desc=  
+
|message_desc=No map output interval has been specified.  Prior to the 2013 version of TUFLOW, this would be output at each timestep.  This command must be specified if not using the <tt><font color="blue">Defaults </font><font color="red">== </font> Pre 2013-12</tt> command.  As of Build 2013-12-AC if “<font color="blue"><tt>Map Output Interval </tt></font><font color="red"><tt>== </tt></font>0” is specified time based map output is switched off.<br>
|suggestions=
+
This can be set for each output format, for example in the below the .xmdf output is every 300 seconds (5minutes) and the temporal output is suppressed for the .asc output (i.e. only the maximums):<br>
|discussion_page=* [[Talk:TUFLOW Message 0045|Discuss Message 0045]]
+
<tt><font color="blue">Map Output Interval </font><font color="red">== </font>3600</tt><br>
|link3=''
+
<tt><font color="blue">XMDF Map Output Interval </font><font color="red">== </font> 300</tt><br>
|link4=''
+
<tt><font color="blue">ASC Map Output Interval </font><font color="red">== </font> 0</tt><br>
|prelink=[[TUFLOW_Message_0043|Message 0043]]
+
If using output zones, the map output interval can be set for each output zone.  However, the Map Output Interval must also be set for the entire model outside of a Define Output Zone / End Define block.
 +
|suggestions=Ensure that a <font color="blue"><tt>Map Output Interval </tt></font><font color="red"><tt>== </tt></font> command is included in the simulation outside of an output zone block of commands.
 +
<br>
 +
 
 
|uplink=[[0xxx_TUFLOW_Messages|0xxx Messages]]
 
|uplink=[[0xxx_TUFLOW_Messages|0xxx Messages]]
|nextlink=[[TUFLOW_Message_0046|Message 0046]]
 
 
}}
 
}}

Latest revision as of 10:04, 22 December 2022

TUFLOW Message
ERROR 0045 - Map Output Interval is not specified.

Alternate Message
NA

Message Type
ERROR

Description
No map output interval has been specified. Prior to the 2013 version of TUFLOW, this would be output at each timestep. This command must be specified if not using the Defaults == Pre 2013-12 command. As of Build 2013-12-AC if “Map Output Interval == 0” is specified time based map output is switched off.
This can be set for each output format, for example in the below the .xmdf output is every 300 seconds (5minutes) and the temporal output is suppressed for the .asc output (i.e. only the maximums):
Map Output Interval == 3600
XMDF Map Output Interval == 300
ASC Map Output Interval == 0
If using output zones, the map output interval can be set for each output zone. However, the Map Output Interval must also be set for the entire model outside of a Define Output Zone / End Define block.

Suggestions
Ensure that a Map Output Interval == command is included in the simulation outside of an output zone block of commands.


Up
Go-up.png 0xxx Messages