Difference between revisions of "TUFLOW Message 2050"
(Created page with '{{TUFLOW_Message |tuflow_message=???? |message_desc="The lowest 2D cell centre elevation (ZC level) at/along the SX 1D/2D interface is above the bed of the connected 1D node or e...') |
|||
| Line 1: | Line 1: | ||
{{TUFLOW_Message | {{TUFLOW_Message | ||
| − | |tuflow_message= | + | |tuflow_message=ERROR 2050 - Lowest ZC elevation at/along SX link is above 1D node bed. |
| + | |alt_msg=WARNING 2050 - Lowest ZC elevation at/along SX link is above 1D node bed. | ||
| + | |type=[[ERROR]] <br> [[WARNING]] | ||
|message_desc="The lowest 2D cell centre elevation (ZC level) at/along the SX 1D/2D interface is above the bed of the connected 1D node or element. The lowest ZC level at or along the 1D/2D interface plus the 2D cell's wet/dry depth must be below the bed of the connected 1D element for SX type 1D/2D connections. SX connections are usually used for embedding small 1D elements such as pipes, culverts and manholes/pits. Treatment of this message as an ERROR or a WARNING is controlled by the ""SX ZC Check"" command. The ZC level of the 2D cell can be automatically lowered using ""Z"" in the Flag attribute for the object - see table of 2d_bc attributes in the manual." | |message_desc="The lowest 2D cell centre elevation (ZC level) at/along the SX 1D/2D interface is above the bed of the connected 1D node or element. The lowest ZC level at or along the 1D/2D interface plus the 2D cell's wet/dry depth must be below the bed of the connected 1D element for SX type 1D/2D connections. SX connections are usually used for embedding small 1D elements such as pipes, culverts and manholes/pits. Treatment of this message as an ERROR or a WARNING is controlled by the ""SX ZC Check"" command. The ZC level of the 2D cell can be automatically lowered using ""Z"" in the Flag attribute for the object - see table of 2d_bc attributes in the manual." | ||
|suggestions=???? | |suggestions=???? | ||
| Line 7: | Line 9: | ||
|link4='' | |link4='' | ||
|prelink=[[TUFLOW_Message_2049|Message 2049]] | |prelink=[[TUFLOW_Message_2049|Message 2049]] | ||
| + | |uplink=[[2xxx_TUFLOW_Messages|2xxx Messages]] | ||
|nextlink=[[TUFLOW_Message_2051|Message 2051]] | |nextlink=[[TUFLOW_Message_2051|Message 2051]] | ||
}} | }} | ||
Revision as of 11:43, 1 October 2010
TUFLOW Message
ERROR 2050 - Lowest ZC elevation at/along SX link is above 1D node bed.
Alternate Message
WARNING 2050 - Lowest ZC elevation at/along SX link is above 1D node bed.
Description
"The lowest 2D cell centre elevation (ZC level) at/along the SX 1D/2D interface is above the bed of the connected 1D node or element. The lowest ZC level at or along the 1D/2D interface plus the 2D cell's wet/dry depth must be below the bed of the connected 1D element for SX type 1D/2D connections. SX connections are usually used for embedding small 1D elements such as pipes, culverts and manholes/pits. Treatment of this message as an ERROR or a WARNING is controlled by the ""SX ZC Check"" command. The ZC level of the 2D cell can be automatically lowered using ""Z"" in the Flag attribute for the object - see table of 2d_bc attributes in the manual."
Suggestions
????
| Up |
|---|
 2xxx Messages
|