FM Tute M02 ARC Boundary Conditions - Revision history

Tuflowduncan: /* Method */

2019-01-04T08:48:33Z

Method

← Older revision		Revision as of 18:48, 4 January 2019
Line 3:		Line 3:
	This page details the method for using ArcGIS to create the GIS based boundary layer. The layer will be populated with the name of each inflow boundary which will be linked to the boundary database in the following steps of this module. The created boundary will be applied as a source-area boundary in a 2d_sa layer. <br>		This page details the method for using ArcGIS to create the GIS based boundary layer. The layer will be populated with the name of each inflow boundary which will be linked to the boundary database in the following steps of this module. The created boundary will be applied as a source-area boundary in a 2d_sa layer. <br>
	=Method=		=Method=
	<li>Copy the layer '''2d_sa_FMT_M02_001_R.shp''' within the '''Module_data\Module_02\Inflow ~~folder~~''' into the '''TUFLOW\model\gis''' folder.		<li>Copy the layer '''2d_sa_FMT_M02_001_R.shp''' within the '''Module_data\Module_02\Inflow''' folder into the '''TUFLOW\model\gis''' folder.
	<li>Open the layer in ArcGIS. Four polygons have been digitised over the location of the proposed development. Each polygon represents a sub-catchment to which different inflow boundaries will be associated. Make the layer '''2d_sa_FMT_M02_001_R''' editable and within the attribute table populate the first and only field of each polygon with the name of the inflow boundary as shown in the figure below. The next steps of this module will link these boundary names with an inflow using the bc_dbase located in '''TUFLOW\bc_dbase''' <br>		<li>Open the layer in ArcGIS. Four polygons have been digitised over the location of the proposed development. Each polygon represents a sub-catchment to which different inflow boundaries will be associated. Make the layer '''2d_sa_FMT_M02_001_R''' editable and within the attribute table populate the first and only field of each polygon with the name of the inflow boundary as shown in the figure below. The next steps of this module will link these boundary names with an inflow using the bc_dbase located in '''TUFLOW\bc_dbase''' <br>
	<br>		<br>

Tuflowduncan at 16:52, 3 January 2019

2019-01-03T16:52:25Z

← Older revision		Revision as of 02:52, 4 January 2019
Line 1:		Line 1:
	<ol>		<ol>
	=Introduction=		=Introduction=
	This page details the method for using ArcGIS to create the GIS based boundary layer. The layer will be populated with the name of each inflow boundary which will be linked to the boundary database ~~(created in [[Module1_test#Define_Boundary_Conditions\|Module 1]])~~ in the following steps of this module. The created boundary will be applied as a source-area boundary in a 2d_sa layer. <br>		This page details the method for using ArcGIS to create the GIS based boundary layer. The layer will be populated with the name of each inflow boundary which will be linked to the boundary database in the following steps of this module. The created boundary will be applied as a source-area boundary in a 2d_sa layer. <br>
	=Method=		=Method=
	<li>Copy the layer '''2d_sa_FMT_M02_001_R.shp''' within the '''Module_data\Module_02\Inflow folder''' into the '''TUFLOW\model\gis''' folder.		<li>Copy the layer '''2d_sa_FMT_M02_001_R.shp''' within the '''Module_data\Module_02\Inflow folder''' into the '''TUFLOW\model\gis''' folder.

Tuflowduncan: /* Conclusion */

2019-01-03T16:45:08Z

Conclusion

← Older revision		Revision as of 02:45, 4 January 2019
Line 23:		Line 23:

	=Conclusion=		=Conclusion=
	A GIS layer has been created containing four polygons in a 2d_sa layer over the location of the proposed development. The existing boundary conditions database (bc_dbase) has been modified to link these four GIS objects to hydrographs within an external csv file. Please return to the main page of the [[~~https://wiki.tuflow.com/index.php?title=~~Flood_Modeller_Tutorial_Module02\| Flood Modeller module 2 tutorial]].		A GIS layer has been created containing four polygons in a 2d_sa layer over the location of the proposed development. The existing boundary conditions database (bc_dbase) has been modified to link these four GIS objects to hydrographs within an external csv file. Please return to the main page of the [[Flood_Modeller_Tutorial_Module02\| Flood Modeller module 2 tutorial]].

	</ol>		</ol>

Tuflowduncan: /* Method */

2019-01-03T16:40:26Z

Method

← Older revision		Revision as of 02:40, 4 January 2019
Line 15:		Line 15:
	<li>We need to add four additional rows to the file which reference the four additional inflows that have been created in the layer '''2d_sa_FMT_M02_001_R'''. The revised bc_dbase should look like the figure below:<br>		<li>We need to add four additional rows to the file which reference the four additional inflows that have been created in the layer '''2d_sa_FMT_M02_001_R'''. The revised bc_dbase should look like the figure below:<br>
	<br>		<br>
	[[File:~~M07 bcdbase~~.png]]<br>		[[File:100yr2hr_loc_csv.png]]<br>
	<br>		<br>
	The hydrographs applied to each of the 2d_sa polygons are contained within the source file '''100yr2hr_loc.csv'''. <br>		The hydrographs applied to each of the 2d_sa polygons are contained within the source file '''100yr2hr_loc.csv'''. <br>

Tuflowduncan: /* Method */

2019-01-03T16:34:40Z

Method

← Older revision		Revision as of 02:34, 4 January 2019
Line 8:		Line 8:
	[[File:M07 SA polygons ARC.png\|700px]]		[[File:M07 SA polygons ARC.png\|700px]]
	<br>		<br>
	<li>Save the layer '''~~2d_sa_M07_001_R~~'''. <br>		<li>Save the layer '''2d_sa_FMT_M02_001_R'''. <br>
	<br>		<br>
	<u>'''Boundary Condition Database'''</u>		<u>'''Boundary Condition Database'''</u>
	<li>Copy the file '''100yr2hr_loc.csv''' from '''Module_data\~~Module_07~~\Inflow''' and place it into the '''TUFLOW\model\bc_dbase''' folder. This file contains the four hydrographs that will be used.		<li>Copy the file '''100yr2hr_loc.csv''' from '''Module_data\Module_02\Inflow''' and place it into the '''TUFLOW\model\bc_dbase''' folder. This file contains the four hydrographs that will be used.
	<li>Open up the ~~latest version of the~~ boundary condition database ~~which was used when simulating the model in Module 6~~. This is located within the '''TUFLOW\model\bc_dbase folder''' and is called '''~~bc_dbase_M04~~.csv'''.		<li>Open up the boundary condition database . This is located within the '''TUFLOW\model\bc_dbase folder''' and is called '''bc_dbase_FMT_M01.csv'''.
	<li>We need to add four additional rows to the file which reference the four additional inflows that have been created in the layer '''~~2d_sa_M07_001_R~~'''. The revised bc_dbase should look like the figure below:<br>		<li>We need to add four additional rows to the file which reference the four additional inflows that have been created in the layer '''2d_sa_FMT_M02_001_R'''. The revised bc_dbase should look like the figure below:<br>
	<br>		<br>
	[[File:M07 bcdbase.png]]<br>		[[File:M07 bcdbase.png]]<br>
Line 20:		Line 20:
	[[File:100yr2hr loc.PNG\|800px]]		[[File:100yr2hr loc.PNG\|800px]]
	<br>		<br>
	<li>Save the bc_dbase as '''~~bc_dbase_M07~~.csv'''. It is now ready to be used within the model.		<li>Save the bc_dbase as '''bc_dbase_FMT_M02.csv'''. It is now ready to be used within the model.

	=Conclusion=		=Conclusion=

Tuflowduncan: Created page with "
=Introduction= This page details the method for using ArcGIS to create the GIS based boundary layer. The layer will be populated with the name of each inflow boundary whi..."

2019-01-03T16:09:23Z

Created page with "<ol> =Introduction= This page details the method for using ArcGIS to create the GIS based boundary layer. The layer will be populated with the name of each inflow boundary whi..."

New page

<ol>
=Introduction=
This page details the method for using ArcGIS to create the GIS based boundary layer. The layer will be populated with the name of each inflow boundary which will be linked to the boundary database (created in [[Module1_test#Define_Boundary_Conditions|Module 1]]) in the following steps of this module. The created boundary will be applied as a source-area boundary in a 2d_sa layer. 
=Method=
<li>Copy the layer '''2d_sa_FMT_M02_001_R.shp''' within the '''Module_data\Module_02\Inflow folder''' into the '''TUFLOW\model\gis''' folder.
<li>Open the layer in ArcGIS. Four polygons have been digitised over the location of the proposed development. Each polygon represents a sub-catchment to which different inflow boundaries will be associated. Make the layer '''2d_sa_FMT_M02_001_R''' editable and within the attribute table populate the first and only field of each polygon with the name of the inflow boundary as shown in the figure below. The next steps of this module will link these boundary names with an inflow using the bc_dbase located in '''TUFLOW\bc_dbase''' 
 
[[File:M07 SA polygons ARC.png|700px]]
 
<li>Save the layer '''2d_sa_M07_001_R'''. 
 
'''Boundary Condition Database'''
<li>Copy the file '''100yr2hr_loc.csv''' from '''Module_data\Module_07\Inflow''' and place it into the '''TUFLOW\model\bc_dbase''' folder. This file contains the four hydrographs that will be used.
<li>Open up the latest version of the boundary condition database which was used when simulating the model in Module 6. This is located within the '''TUFLOW\model\bc_dbase folder''' and is called '''bc_dbase_M04.csv'''.
<li>We need to add four additional rows to the file which reference the four additional inflows that have been created in the layer '''2d_sa_M07_001_R'''. The revised bc_dbase should look like the figure below: 
 
[[File:M07 bcdbase.png]] 
 
The hydrographs applied to each of the 2d_sa polygons are contained within the source file '''100yr2hr_loc.csv'''. 
[[File:100yr2hr loc.PNG|800px]]
 
<li>Save the bc_dbase as '''bc_dbase_M07.csv'''. It is now ready to be used within the model.

=Conclusion=
A GIS layer has been created containing four polygons in a 2d_sa layer over the location of the proposed development. The existing boundary conditions database (bc_dbase) has been modified to link these four GIS objects to hydrographs within an external csv file. Please return to the main page of the [[https://wiki.tuflow.com/index.php?title=Flood_Modeller_Tutorial_Module02| Flood Modeller module 2 tutorial]].

</ol>

FM Tute M02 ARC Boundary Conditions - Revision history

Tuflowduncan: /* Method */

Tuflowduncan at 16:52, 3 January 2019

Tuflowduncan: /* Conclusion */

Tuflowduncan: /* Method */

Tuflowduncan: /* Method */

Tuflowduncan: Created page with " =Introduction= This page details the method for using ArcGIS to create the GIS based boundary layer. The layer will be populated with the name of each inflow boundary whi..."

Tuflowduncan: Created page with "
=Introduction= This page details the method for using ArcGIS to create the GIS based boundary layer. The layer will be populated with the name of each inflow boundary whi..."