TUFLOW Message 1262 - Revision history

Melissa.Moghanloo at 06:00, 22 December 2022

2022-12-22T06:00:35Z

← Older revision		Revision as of 16:00, 22 December 2022
Line 6:		Line 6:
	\|suggestions=Check Manning's n value for channel. If material values are defined in the XZ cross-section ("M" flag), the n_or_n_F attribute in the 1d_nwk is a multiplication factor and should be set to 1 (this may be adjusted as part of the calibration process). This can occur if a the multiplication value is set to a typical Manning's value (e.g. 0.04) and materials are defined in the XZM cross-section. In this case the Manning's n value may become 0.04 x 0.04 = 0.0016!		\|suggestions=Check Manning's n value for channel. If material values are defined in the XZ cross-section ("M" flag), the n_or_n_F attribute in the 1d_nwk is a multiplication factor and should be set to 1 (this may be adjusted as part of the calibration process). This can occur if a the multiplication value is set to a typical Manning's value (e.g. 0.04) and materials are defined in the XZM cross-section. In this case the Manning's n value may become 0.04 x 0.04 = 0.0016!


	\|prelink=[[TUFLOW_Message_1261\|Message 1261]]
	\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]		\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]
	\|nextlink=[[TUFLOW_Message_1264\|Message 1264]]
	}}		}}

Melissa.Moghanloo at 04:39, 5 July 2022

2022-07-05T04:39:05Z

← Older revision		Revision as of 14:39, 5 July 2022
Line 5:		Line 5:
	\|message_desc=Manning's n value assigned to channel is outside normal range.		\|message_desc=Manning's n value assigned to channel is outside normal range.
	\|suggestions=Check Manning's n value for channel. If material values are defined in the XZ cross-section ("M" flag), the n_or_n_F attribute in the 1d_nwk is a multiplication factor and should be set to 1 (this may be adjusted as part of the calibration process). This can occur if a the multiplication value is set to a typical Manning's value (e.g. 0.04) and materials are defined in the XZM cross-section. In this case the Manning's n value may become 0.04 x 0.04 = 0.0016!		\|suggestions=Check Manning's n value for channel. If material values are defined in the XZ cross-section ("M" flag), the n_or_n_F attribute in the 1d_nwk is a multiplication factor and should be set to 1 (this may be adjusted as part of the calibration process). This can occur if a the multiplication value is set to a typical Manning's value (e.g. 0.04) and materials are defined in the XZM cross-section. In this case the Manning's n value may become 0.04 x 0.04 = 0.0016!

	\|discussion_page=* [[Talk:TUFLOW Message 1262\|Discuss Message 1262]]
	\|link3=''
	\|link4=''
	\|prelink=[[TUFLOW_Message_1261\|Message 1261]]		\|prelink=[[TUFLOW_Message_1261\|Message 1261]]
	\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]		\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]

tuflow>Par at 04:04, 2 February 2011

2011-02-02T04:04:48Z

← Older revision		Revision as of 14:04, 2 February 2011
Line 1:		Line 1:
	{{TUFLOW_Message		{{TUFLOW_Message
	\|tuflow_message=WARNING 1262 - Manning's n value of ~~",a,"~~ for channel ~~",a,"~~ is unusually low or high.		\|tuflow_message=WARNING 1262 - Manning's n value of <Manning's n value> for channel <Channel ID> is unusually low or high.
	\|alt_msg=NA		\|alt_msg=NA
	\|type=[[WARNING]]		\|type=[[WARNING]]

tuflow>Par: Protected "TUFLOW Message 1262" ([edit=sysop] (indefinite) [move=sysop] (indefinite))

2011-02-02T02:15:52Z

Protected "TUFLOW Message 1262" ([edit=sysop] (indefinite) [move=sysop] (indefinite))

← Older revision		Revision as of 12:15, 2 February 2011
(No difference)

tuflow>Par at 23:33, 1 February 2011

2011-02-01T23:33:13Z

← Older revision		Revision as of 09:33, 2 February 2011
Line 4:		Line 4:
	\|type=[[WARNING]]		\|type=[[WARNING]]
	\|message_desc=Manning's n value assigned to channel is outside normal range.		\|message_desc=Manning's n value assigned to channel is outside normal range.
	\|suggestions=Check Manning's n value for channel. If material values are defined in the XZ cross-section ("M" flag), the n_or_n_F attribute in the 1d_nwk is a multiplication factor and should be set to 1 (this may be adjusted as part of the calibration process). This can occur if a the multiplication value is set to a typical ~~Mannings~~ value (e.g. 0.04) and materials are defined in the XZM cross-section. In this case the ~~Mannings~~ n value may become 0.04 x 0.04 = 0.0016!		\|suggestions=Check Manning's n value for channel. If material values are defined in the XZ cross-section ("M" flag), the n_or_n_F attribute in the 1d_nwk is a multiplication factor and should be set to 1 (this may be adjusted as part of the calibration process). This can occur if a the multiplication value is set to a typical Manning's value (e.g. 0.04) and materials are defined in the XZM cross-section. In this case the Manning's n value may become 0.04 x 0.04 = 0.0016!
	\|discussion_page=* [[Talk:TUFLOW Message 1262\|Discuss Message 1262]]		\|discussion_page=* [[Talk:TUFLOW Message 1262\|Discuss Message 1262]]
	\|link3=''		\|link3=''

tuflow>Par at 23:32, 1 February 2011

2011-02-01T23:32:51Z

← Older revision		Revision as of 09:32, 2 February 2011
Line 3:		Line 3:
	\|alt_msg=NA		\|alt_msg=NA
	\|type=[[WARNING]]		\|type=[[WARNING]]
	\|message_desc=Manning's n value assigned to channel, is outside normal range.		\|message_desc=Manning's n value assigned to channel is outside normal range.
	\|suggestions=Check Manning's n value for channel. If material values are defined in the XZ cross-section ("M" flag), the n_or_n_F attribute in the 1d_nwk is a multiplication factor and should be set to 1 (this may be adjusted as part of the calibration process). This can occur if a the multiplication value is set to a typical Mannings value (e.g. 0.04) and materials are defined in the XZM cross-section. In this case the Mannings n value may become 0.04 x 0.04 = 0.0016!		\|suggestions=Check Manning's n value for channel. If material values are defined in the XZ cross-section ("M" flag), the n_or_n_F attribute in the 1d_nwk is a multiplication factor and should be set to 1 (this may be adjusted as part of the calibration process). This can occur if a the multiplication value is set to a typical Mannings value (e.g. 0.04) and materials are defined in the XZM cross-section. In this case the Mannings n value may become 0.04 x 0.04 = 0.0016!
	\|discussion_page=* [[Talk:TUFLOW Message 1262\|Discuss Message 1262]]		\|discussion_page=* [[Talk:TUFLOW Message 1262\|Discuss Message 1262]]

tuflow>Par at 23:32, 1 February 2011

2011-02-01T23:32:34Z

← Older revision		Revision as of 09:32, 2 February 2011
Line 3:		Line 3:
	\|alt_msg=NA		\|alt_msg=NA
	\|type=[[WARNING]]		\|type=[[WARNING]]
			\|message_desc=Manning's n value assigned to channel, is outside normal range.
	\|message_desc=????
			\|suggestions=Check Manning's n value for channel. If material values are defined in the XZ cross-section ("M" flag), the n_or_n_F attribute in the 1d_nwk is a multiplication factor and should be set to 1 (this may be adjusted as part of the calibration process). This can occur if a the multiplication value is set to a typical Mannings value (e.g. 0.04) and materials are defined in the XZM cross-section. In this case the Mannings n value may become 0.04 x 0.04 = 0.0016!
	\|suggestions=????
	\|discussion_page=* [[Talk:TUFLOW Message 1262\|Discuss Message 1262]]		\|discussion_page=* [[Talk:TUFLOW Message 1262\|Discuss Message 1262]]
	\|link3=''		\|link3=''

tuflow>Par at 03:59, 2 December 2010

2010-12-02T03:59:50Z

← Older revision		Revision as of 13:59, 2 December 2010
Line 1:		Line 1:
	{{TUFLOW_Message		{{TUFLOW_Message
	\|tuflow_message=WARNING 1262 - Manning''s n value of ",a," for channel ",a," is unusually low or high.		\|tuflow_message=WARNING 1262 - Manning's n value of ",a," for channel ",a," is unusually low or high.
	\|alt_msg=NA		\|alt_msg=NA
	\|type=[[WARNING]]		\|type=[[WARNING]]

tuflow>Par: Created page with '{{TUFLOW_Message |tuflow_message=WARNING 1262 - Manning''s n value of ",a," for channel ",a," is unusually low or high. |alt_msg=NA |type=WARNING |message_desc=???? |suggesti...'

2010-09-30T23:25:05Z

Created page with '{{TUFLOW_Message |tuflow_message=WARNING 1262 - Manning''s n value of ",a," for channel ",a," is unusually low or high. |alt_msg=NA |type=WARNING |message_desc=???? |suggesti...'

New page

{{TUFLOW_Message
|tuflow_message=WARNING 1262 - Manning''s n value of ",a," for channel ",a," is unusually low or high.
|alt_msg=NA
|type=[[WARNING]]
|message_desc=????
|suggestions=????
|discussion_page=* [[Talk:TUFLOW Message 1262|Discuss Message 1262]]
|link3=''
|link4=''
|prelink=[[TUFLOW_Message_1261|Message 1261]]
|uplink=[[1xxx_TUFLOW_Messages|1xxx Messages]]
|nextlink=[[TUFLOW_Message_1264|Message 1264]]
}}