TUFLOW Message 1370 - Revision history

Anne.Kolega: e.g.

2026-04-01T04:42:29Z

e.g.

← Older revision		Revision as of 14:42, 1 April 2026
Line 3:		Line 3:
	\|alt_msg=NA		\|alt_msg=NA
	\|type=[[ERROR]]		\|type=[[ERROR]]
	\|message_desc=Channel ID as set by the ID attribute in the 1D network layer is not unique. This should be a unique identifier up to 12 characters in length. It may contain any character except for quotes and commas, and cannot be blank. As a general rule, spaces and special characters (eg. “\”) should be avoided, although they are accepted. The same ID can be used for a channel and a node, but no two nodes and no two channels can have the same ID.<br>		\|message_desc=Channel ID as set by the ID attribute in the 1D network layer is not unique. This should be a unique identifier up to 12 characters in length. It may contain any character except for quotes and commas, and cannot be blank. As a general rule, spaces and special characters (e.g. “\”) should be avoided, although they are accepted. The same ID can be used for a channel and a node, but no two nodes and no two channels can have the same ID.<br>
	<br>		<br>
	This error may also occur with automatically created 1d nodes. If a node has not been digitised at the end of a channel a new node is automatically created. The ID of automatic nodes is the first ten characters of the Channel ID with a “.1” or “.2” extension. “.1” is used if the node is at the start of the channel and “.2” if at the end. If more than one channel is connected to the created node, the Channel ID that occurs first alphanumerically is used.		This error may also occur with automatically created 1d nodes. If a node has not been digitised at the end of a channel a new node is automatically created. The ID of automatic nodes is the first ten characters of the Channel ID with a “.1” or “.2” extension. “.1” is used if the node is at the start of the channel and “.2” if at the end. If more than one channel is connected to the created node, the Channel ID that occurs first alphanumerically is used.

Melissa.Moghanloo at 00:38, 23 December 2022

2022-12-23T00:38:34Z

← Older revision		Revision as of 10:38, 23 December 2022
Line 8:		Line 8:
	\|suggestions=Check channels have a unique ID, if this message is occuring at an automatically created node, you may need to have channel ID's that are 10 characters and unique. This ensures that when the nodes are created these also have unique IDs.		\|suggestions=Check channels have a unique ID, if this message is occuring at an automatically created node, you may need to have channel ID's that are 10 characters and unique. This ensures that when the nodes are created these also have unique IDs.


	\|prelink=[[TUFLOW_Message_1363\|Message 1363]]
	\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]		\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]
	\|nextlink=[[TUFLOW_Message_1371\|Message 1371]]
	}}		}}

Melissa.Moghanloo at 05:45, 5 July 2022

2022-07-05T05:45:09Z

← Older revision		Revision as of 15:45, 5 July 2022
Line 7:		Line 7:
	This error may also occur with automatically created 1d nodes. If a node has not been digitised at the end of a channel a new node is automatically created. The ID of automatic nodes is the first ten characters of the Channel ID with a “.1” or “.2” extension. “.1” is used if the node is at the start of the channel and “.2” if at the end. If more than one channel is connected to the created node, the Channel ID that occurs first alphanumerically is used.		This error may also occur with automatically created 1d nodes. If a node has not been digitised at the end of a channel a new node is automatically created. The ID of automatic nodes is the first ten characters of the Channel ID with a “.1” or “.2” extension. “.1” is used if the node is at the start of the channel and “.2” if at the end. If more than one channel is connected to the created node, the Channel ID that occurs first alphanumerically is used.
	\|suggestions=Check channels have a unique ID, if this message is occuring at an automatically created node, you may need to have channel ID's that are 10 characters and unique. This ensures that when the nodes are created these also have unique IDs.		\|suggestions=Check channels have a unique ID, if this message is occuring at an automatically created node, you may need to have channel ID's that are 10 characters and unique. This ensures that when the nodes are created these also have unique IDs.

	\|discussion_page=* [[Talk:TUFLOW Message 1370\|Discuss Message 1370]]
	\|link3=''
	\|link4=''
	\|prelink=[[TUFLOW_Message_1363\|Message 1363]]		\|prelink=[[TUFLOW_Message_1363\|Message 1363]]
	\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]		\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]

tuflow>Par at 05:20, 3 February 2011

2011-02-03T05:20:33Z

← Older revision		Revision as of 15:20, 3 February 2011
Line 4:		Line 4:
	\|type=[[ERROR]]		\|type=[[ERROR]]
	\|message_desc=Channel ID as set by the ID attribute in the 1D network layer is not unique. This should be a unique identifier up to 12 characters in length. It may contain any character except for quotes and commas, and cannot be blank. As a general rule, spaces and special characters (eg. “\”) should be avoided, although they are accepted. The same ID can be used for a channel and a node, but no two nodes and no two channels can have the same ID.<br>		\|message_desc=Channel ID as set by the ID attribute in the 1D network layer is not unique. This should be a unique identifier up to 12 characters in length. It may contain any character except for quotes and commas, and cannot be blank. As a general rule, spaces and special characters (eg. “\”) should be avoided, although they are accepted. The same ID can be used for a channel and a node, but no two nodes and no two channels can have the same ID.<br>
			<br>
	This error may also occur with automatically created 1d nodes. If a node has not been digitised at the end of a channel a new node is automatically created. The ID of automatic nodes is the first ten characters of the Channel ID with a “.1” or “.2” extension. “.1” is used if the node is at the start of the channel and “.2” if at the end. If more than one channel is connected to the created node, the Channel ID that occurs first alphanumerically is used.		This error may also occur with automatically created 1d nodes. If a node has not been digitised at the end of a channel a new node is automatically created. The ID of automatic nodes is the first ten characters of the Channel ID with a “.1” or “.2” extension. “.1” is used if the node is at the start of the channel and “.2” if at the end. If more than one channel is connected to the created node, the Channel ID that occurs first alphanumerically is used.
	\|suggestions=Check channels have a unique ID, if this message is occuring at an automatically created node, you may need to have channel ID's that are 10 characters and unique. This ensures that when the nodes are created these also have unique IDs.		\|suggestions=Check channels have a unique ID, if this message is occuring at an automatically created node, you may need to have channel ID's that are 10 characters and unique. This ensures that when the nodes are created these also have unique IDs.

tuflow>Par at 05:20, 3 February 2011

2011-02-03T05:20:16Z

← Older revision		Revision as of 15:20, 3 February 2011
Line 3:		Line 3:
	\|alt_msg=NA		\|alt_msg=NA
	\|type=[[ERROR]]		\|type=[[ERROR]]
			\|message_desc=Channel ID as set by the ID attribute in the 1D network layer is not unique. This should be a unique identifier up to 12 characters in length. It may contain any character except for quotes and commas, and cannot be blank. As a general rule, spaces and special characters (eg. “\”) should be avoided, although they are accepted. The same ID can be used for a channel and a node, but no two nodes and no two channels can have the same ID.<br>
	\|message_desc=????
			This error may also occur with automatically created 1d nodes. If a node has not been digitised at the end of a channel a new node is automatically created. The ID of automatic nodes is the first ten characters of the Channel ID with a “.1” or “.2” extension. “.1” is used if the node is at the start of the channel and “.2” if at the end. If more than one channel is connected to the created node, the Channel ID that occurs first alphanumerically is used.
	\|suggestions=????
			\|suggestions=Check channels have a unique ID, if this message is occuring at an automatically created node, you may need to have channel ID's that are 10 characters and unique. This ensures that when the nodes are created these also have unique IDs.
	\|discussion_page=* [[Talk:TUFLOW Message 1370\|Discuss Message 1370]]		\|discussion_page=* [[Talk:TUFLOW Message 1370\|Discuss Message 1370]]
	\|link3=''		\|link3=''

tuflow>Par: Created page with '{{TUFLOW_Message |tuflow_message=ERROR 1370 - ",a," ID ",a," occurs ",a," times (IDs must be unique). |alt_msg=NA |type=ERROR |message_desc=???? |suggestions=???? |discussion...'

2010-09-30T23:34:56Z

Created page with '{{TUFLOW_Message |tuflow_message=ERROR 1370 - ",a," ID ",a," occurs ",a," times (IDs must be unique). |alt_msg=NA |type=ERROR |message_desc=???? |suggestions=???? |discussion...'

New page

{{TUFLOW_Message
|tuflow_message=ERROR 1370 - ",a," ID ",a," occurs ",a," times (IDs must be unique).
|alt_msg=NA
|type=[[ERROR]]
|message_desc=????
|suggestions=????
|discussion_page=* [[Talk:TUFLOW Message 1370|Discuss Message 1370]]
|link3=''
|link4=''
|prelink=[[TUFLOW_Message_1363|Message 1363]]
|uplink=[[1xxx_TUFLOW_Messages|1xxx Messages]]
|nextlink=[[TUFLOW_Message_1371|Message 1371]]
}}