TUFLOW Message 1402 - Revision history

Emilie Nielsen at 23:51, 22 September 2024

2024-09-22T23:51:05Z

← Older revision		Revision as of 09:51, 23 September 2024
Line 3:		Line 3:
	\|alt_msg=NA		\|alt_msg=NA
	\|type=[[CHECK]]		\|type=[[CHECK]]
	\|message_desc=When applying the Engelhund loss approach for manholes (~~see~~ ~~Section~~ 4.5.~~2 of the 2010~~ TUFLOW ~~manual~~), if an incoming culvert enters above the obvert of the highest outlet, the culvert is not included in the manhole loss calculations. If there is only 1 incoming pipe with the invert above the obvert of the outlet culvert, the incoming culvert is ignored and with no inlet culvert to the node a manhole is not possible. ~~See also point 48(b) in the <u>[https://www.tuflow.com/Download/TUFLOW/Releases/2012-05/Doc/TUFLOW%20Release%20Notes.2011-09%20and%202012-05.pdf release notes]</u>.~~		\|message_desc=When applying the Engelhund loss approach for manholes (refer to the <u>[https://docs.tuflow.com/classic-hpc/manual/latest/ TUFLOW Manual]</u>), if an incoming culvert enters above the obvert of the highest outlet, the culvert is not included in the manhole loss calculations. If there is only 1 incoming pipe with the invert above the obvert of the outlet culvert, the incoming culvert is ignored and with no inlet culvert to the node a manhole is not possible.
	\|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.		\|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.

Emilie Nielsen at 04:47, 18 July 2024

2024-07-18T04:47:04Z

← Older revision		Revision as of 14:47, 18 July 2024
Line 3:		Line 3:
	\|alt_msg=NA		\|alt_msg=NA
	\|type=[[CHECK]]		\|type=[[CHECK]]
	\|message_desc=When applying the Engelhund loss approach for manholes (see Section 4.5.2 of the 2010 TUFLOW manual), if an incoming culvert enters above the obvert of the highest outlet, the culvert is not included in the manhole loss calculations. If there is only 1 incoming pipe with the invert above the obvert of the outlet culvert, the incoming culvert is ignored and with no inlet culvert to the node a manhole is not possible. See also point 48(b) in the <u>[~~http~~://www.tuflow.com/Download/TUFLOW/Releases/2012-05/Doc/TUFLOW%20Release%20Notes.2011-09%20and%202012-05.pdf release notes]</u>.		\|message_desc=When applying the Engelhund loss approach for manholes (see Section 4.5.2 of the 2010 TUFLOW manual), if an incoming culvert enters above the obvert of the highest outlet, the culvert is not included in the manhole loss calculations. If there is only 1 incoming pipe with the invert above the obvert of the outlet culvert, the incoming culvert is ignored and with no inlet culvert to the node a manhole is not possible. See also point 48(b) in the <u>[https://www.tuflow.com/Download/TUFLOW/Releases/2012-05/Doc/TUFLOW%20Release%20Notes.2011-09%20and%202012-05.pdf release notes]</u>.
	\|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.		\|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.

Melissa.Moghanloo at 00:40, 23 December 2022

2022-12-23T00:40:58Z

← Older revision		Revision as of 10:40, 23 December 2022
Line 6:		Line 6:
	\|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.		\|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.


	\|prelink=[[TUFLOW_Message_1401\|Message 1401]]
	\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]		\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]
	\|nextlink=[[TUFLOW_Message_1421\|Message 1421]]
	}}		}}

Melissa.Moghanloo at 05:46, 5 July 2022

2022-07-05T05:46:57Z

← Older revision		Revision as of 15:46, 5 July 2022
Line 5:		Line 5:
	\|message_desc=When applying the Engelhund loss approach for manholes (see Section 4.5.2 of the 2010 TUFLOW manual), if an incoming culvert enters above the obvert of the highest outlet, the culvert is not included in the manhole loss calculations. If there is only 1 incoming pipe with the invert above the obvert of the outlet culvert, the incoming culvert is ignored and with no inlet culvert to the node a manhole is not possible. See also point 48(b) in the <u>[http://www.tuflow.com/Download/TUFLOW/Releases/2012-05/Doc/TUFLOW%20Release%20Notes.2011-09%20and%202012-05.pdf release notes]</u>.		\|message_desc=When applying the Engelhund loss approach for manholes (see Section 4.5.2 of the 2010 TUFLOW manual), if an incoming culvert enters above the obvert of the highest outlet, the culvert is not included in the manhole loss calculations. If there is only 1 incoming pipe with the invert above the obvert of the outlet culvert, the incoming culvert is ignored and with no inlet culvert to the node a manhole is not possible. See also point 48(b) in the <u>[http://www.tuflow.com/Download/TUFLOW/Releases/2012-05/Doc/TUFLOW%20Release%20Notes.2011-09%20and%202012-05.pdf release notes]</u>.
	\|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.		\|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.

	\|discussion_page=* [[Talk:TUFLOW Message 1402\|Discuss Message 1402]]
	\|link3=''
	\|link4=''
	\|prelink=[[TUFLOW_Message_1401\|Message 1401]]		\|prelink=[[TUFLOW_Message_1401\|Message 1401]]
	\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]		\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]

Melissa.Moghanloo at 23:02, 3 July 2022

2022-07-03T23:02:22Z

← Older revision		Revision as of 09:02, 4 July 2022
Line 3:		Line 3:
	\|alt_msg=NA		\|alt_msg=NA
	\|type=[[CHECK]]		\|type=[[CHECK]]
	\|message_desc=When applying the Engelhund loss approach for manholes (see Section 4.5.2 of the 2010 TUFLOW manual), if an incoming culvert enters above the obvert of the highest outlet, the culvert is not included in the manhole loss calculations. If there is only 1 incoming pipe with the invert above the obvert of the outlet culvert, the incoming culvert is ignored and with no inlet culvert to the node a manhole is not possible. See also point 48(b) in the [http://www.tuflow.com/Download/TUFLOW/Releases/2012-05/Doc/TUFLOW%20Release%20Notes.2011-09%20and%202012-05.pdf release notes].		\|message_desc=When applying the Engelhund loss approach for manholes (see Section 4.5.2 of the 2010 TUFLOW manual), if an incoming culvert enters above the obvert of the highest outlet, the culvert is not included in the manhole loss calculations. If there is only 1 incoming pipe with the invert above the obvert of the outlet culvert, the incoming culvert is ignored and with no inlet culvert to the node a manhole is not possible. See also point 48(b) in the <u>[http://www.tuflow.com/Download/TUFLOW/Releases/2012-05/Doc/TUFLOW%20Release%20Notes.2011-09%20and%202012-05.pdf release notes]</u>.
	\|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.		\|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.
	\|discussion_page=* [[Talk:TUFLOW Message 1402\|Discuss Message 1402]]		\|discussion_page=* [[Talk:TUFLOW Message 1402\|Discuss Message 1402]]

Pavlina Monhartova at 23:18, 15 October 2018

2018-10-15T23:18:23Z

← Older revision		Revision as of 09:18, 16 October 2018
Line 10:		Line 10:
	\|prelink=[[TUFLOW_Message_1401\|Message 1401]]		\|prelink=[[TUFLOW_Message_1401\|Message 1401]]
	\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]		\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]
	\|nextlink=[[~~TUFLOW_Message_1510~~\|Message ~~1510~~]]		\|nextlink=[[TUFLOW_Message_1421\|Message 1421]]
	}}		}}

Steph.dufour at 23:20, 2 February 2015

2015-02-02T23:20:44Z

← Older revision		Revision as of 09:20, 3 February 2015
Line 10:		Line 10:
	\|prelink=[[TUFLOW_Message_1401\|Message 1401]]		\|prelink=[[TUFLOW_Message_1401\|Message 1401]]
	\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]		\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]
	\|nextlink=[[~~TUFLOW_Message_1527~~\|Message ~~1527~~]]		\|nextlink=[[TUFLOW_Message_1510\|Message 1510]]
	}}		}}

Steph.dufour at 03:40, 2 February 2015

2015-02-02T03:40:57Z

← Older revision		Revision as of 13:40, 2 February 2015
Line 10:		Line 10:
	\|prelink=[[TUFLOW_Message_1401\|Message 1401]]		\|prelink=[[TUFLOW_Message_1401\|Message 1401]]
	\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]		\|uplink=[[1xxx_TUFLOW_Messages\|1xxx Messages]]
	\|nextlink=[[~~TUFLOW_Message_1991~~\|Message ~~1991~~]]		\|nextlink=[[TUFLOW_Message_1527\|Message 1527]]
	}}		}}

Par: Created page with "{{TUFLOW_Message |tuflow_message=CHECK 1402 - More than one culvert connected but could not create manhole at Node |alt_msg=NA |type=CHECK |message_desc=When app..."

2013-09-03T03:23:10Z

Created page with "{{TUFLOW_Message |tuflow_message=CHECK 1402 - More than one culvert connected but could not create manhole at Node <Node ID> |alt_msg=NA |type=CHECK |message_desc=When app..."

New page

{{TUFLOW_Message
|tuflow_message=CHECK 1402 - More than one culvert connected but could not create manhole at Node <Node ID>
|alt_msg=NA
|type=[[CHECK]]
|message_desc=When applying the Engelhund loss approach for manholes (see Section 4.5.2 of the 2010 TUFLOW manual), if an incoming culvert enters above the obvert of the highest outlet, the culvert is not included in the manhole loss calculations. If there is only 1 incoming pipe with the invert above the obvert of the outlet culvert, the incoming culvert is ignored and with no inlet culvert to the node a manhole is not possible. See also point 48(b) in the [http://www.tuflow.com/Download/TUFLOW/Releases/2012-05/Doc/TUFLOW%20Release%20Notes.2011-09%20and%202012-05.pdf release notes].
|suggestions=Review the inverts on the culverts. A point object in a "1d_mh" layer can be used to set the loss approach at each manhole.
|discussion_page=* [[Talk:TUFLOW Message 1402|Discuss Message 1402]]
|link3=''
|link4=''
|prelink=[[TUFLOW_Message_1401|Message 1401]]
|uplink=[[1xxx_TUFLOW_Messages|1xxx Messages]]
|nextlink=[[TUFLOW_Message_1991|Message 1991]]
}}