TUFLOW Message 3038 - Revision history

Melissa.Moghanloo at 00:17, 3 March 2023

2023-03-03T00:17:29Z

← Older revision		Revision as of 10:17, 3 March 2023
Line 13:		Line 13:
	\|suggestions=Review the applied face width factors and ensure none are less than 0.		\|suggestions=Review the applied face width factors and ensure none are less than 0.

	\|prelink=[[TUFLOW_Message_3037\|Message 3037]]
	\|uplink=[[3xxx_TUFLOW_Messages\|3xxx Messages]]		\|uplink=[[3xxx_TUFLOW_Messages\|3xxx Messages]]
	\|nextlink=[[TUFLOW_Message_3039\|Message 3039]]
	}}		}}

Emilie Nielsen at 06:36, 2 March 2023

2023-03-02T06:36:15Z

← Older revision		Revision as of 16:36, 2 March 2023
Line 1:		Line 1:
	{{TUFLOW_Message		{{TUFLOW_Message
	\|tuflow_message=ERROR 3038: Flow width factors must be >= 0.		\|tuflow_message=ERROR 3038 - Flow width factors must be >= 0.
	<br>		<br>
	\|alt_msg=~~None~~		\|alt_msg=NA<br>

	\|type=[[ERROR]]		\|type=[[ERROR]]
			\|message_desc=Faces may have a flow width factor applied to represent reduced available flow area of the face (for example, if a building occupies part of the face).The changed flow width applies at all depths.<br>
	\|message_desc=The value of specified Cell Width Factor must be greater than 0.0.
			:For example, a factor of 0.1 will limit the flow width to 10%. <br>
	\|suggestions=The Cell Width Factor can be used to adjust the 2D cell flow widths. It is a factor, for example 0.1 will limit the flow width to 10%. The changed flow width applies to all depths. When reading from a polygon object in GIS format, any cell sides that fall within the polygon will have the width factor applied. These factors can be reviewed within the uvpt_check file.
			When reading from a polygon object in GIS format, any cell sides that fall within the polygon will have the width factor
			applied. These factors can be reviewed within the uvpt_check file, and logically cannot be negative.
			Negative factors are not permissible.

			\|suggestions=Review the applied face width factors and ensure none are less than 0.

	\|prelink=[[TUFLOW_Message_3037\|Message 3037]]		\|prelink=[[TUFLOW_Message_3037\|Message 3037]]

Melissa.Moghanloo at 05:21, 13 July 2022

2022-07-13T05:21:33Z

← Older revision		Revision as of 15:21, 13 July 2022
Line 8:		Line 8:
	\|suggestions=The Cell Width Factor can be used to adjust the 2D cell flow widths. It is a factor, for example 0.1 will limit the flow width to 10%. The changed flow width applies to all depths. When reading from a polygon object in GIS format, any cell sides that fall within the polygon will have the width factor applied. These factors can be reviewed within the uvpt_check file.		\|suggestions=The Cell Width Factor can be used to adjust the 2D cell flow widths. It is a factor, for example 0.1 will limit the flow width to 10%. The changed flow width applies to all depths. When reading from a polygon object in GIS format, any cell sides that fall within the polygon will have the width factor applied. These factors can be reviewed within the uvpt_check file.

	\|discussion_page=* [[Talk:TUFLOW Message 3038\|Discuss Message 3038]]
	\|link3=''
	\|link4=''
	\|prelink=[[TUFLOW_Message_3037\|Message 3037]]		\|prelink=[[TUFLOW_Message_3037\|Message 3037]]
	\|uplink=[[3xxx_TUFLOW_Messages\|3xxx Messages]]		\|uplink=[[3xxx_TUFLOW_Messages\|3xxx Messages]]

Teegan.Burke: Created page with "{{TUFLOW_Message |tuflow_message=ERROR 3038: Flow width factors must be >= 0.
|alt_msg=None |type=ERROR |message_desc=The value of specified Cell Width Factor must..."

2018-04-20T00:17:49Z

Created page with "{{TUFLOW_Message |tuflow_message=ERROR 3038: Flow width factors must be >= 0. <br> |alt_msg=None |type=ERROR |message_desc=The value of specified Cell Width Factor must..."

New page

{{TUFLOW_Message
|tuflow_message=ERROR 3038: Flow width factors must be >= 0.
<br>
|alt_msg=None

|type=[[ERROR]]
|message_desc=The value of specified Cell Width Factor must be greater than 0.0.
|suggestions=The Cell Width Factor can be used to adjust the 2D cell flow widths. It is a factor, for example 0.1 will limit the flow width to 10%. The changed flow width applies to all depths. When reading from a polygon object in GIS format, any cell sides that fall within the polygon will have the width factor applied. These factors can be reviewed within the uvpt_check file.

|discussion_page=* [[Talk:TUFLOW Message 3038|Discuss Message 3038]]
|link3=''
|link4=''
|prelink=[[TUFLOW_Message_3037|Message 3037]]
|uplink=[[3xxx_TUFLOW_Messages|3xxx Messages]]
|nextlink=[[TUFLOW_Message_3039|Message 3039]]
}}

TUFLOW Message 3038 - Revision history

Melissa.Moghanloo at 00:17, 3 March 2023

Emilie Nielsen at 06:36, 2 March 2023

Melissa.Moghanloo at 05:21, 13 July 2022

Teegan.Burke: Created page with "{{TUFLOW_Message |tuflow_message=ERROR 3038: Flow width factors must be >= 0. |alt_msg=None |type=ERROR |message_desc=The value of specified Cell Width Factor must..."

Teegan.Burke: Created page with "{{TUFLOW_Message |tuflow_message=ERROR 3038: Flow width factors must be >= 0.
|alt_msg=None |type=ERROR |message_desc=The value of specified Cell Width Factor must..."