TUFLOW Message 3520 - Revision history

Melissa.Moghanloo at 00:26, 3 March 2023

2023-03-03T00:26:57Z

← Older revision		Revision as of 10:26, 3 March 2023
Line 7:		Line 7:
	\|suggestions=Although TUFLOW automatically correct the face elevations, users can turn <font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>ON</tt> (the default is "<tt>OFF</tt>") to report every faces with the issue to the _message_p layer. If the geometries input layers are all correctly set around these faces, turn <font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt> to omit this warning message.		\|suggestions=Although TUFLOW automatically correct the face elevations, users can turn <font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>ON</tt> (the default is "<tt>OFF</tt>") to report every faces with the issue to the _message_p layer. If the geometries input layers are all correctly set around these faces, turn <font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt> to omit this warning message.

	\|prelink=[[TUFLOW_Message_3519\|Message 3519]]
	\|uplink=[[3xxx_TUFLOW_Messages\|3xxx Messages]]		\|uplink=[[3xxx_TUFLOW_Messages\|3xxx Messages]]
	\|nextlink=[[TUFLOW_Message_3521\|Message 3521]]
	}}		}}

Emilie Nielsen at 00:12, 2 March 2023

2023-03-02T00:12:38Z

← Older revision		Revision as of 10:12, 2 March 2023
Line 1:		Line 1:
	{{TUFLOW_Message		{{TUFLOW_Message
	\|tuflow_message=CHECK 3520 - Found SGS cell face that has minimum Face elevation lower than the minimum cell centre elevations on both sides.		\|tuflow_message=CHECK 3520 - Found SGS cell face that has minimum Face elevation lower than the minimum cell centre elevations on both sides.
	\|alt_msg=Minimum U elevation must be higher than the minimum cell centre elevations on both sides in SGS. ZCmin left = "a", ZUmin = "b", ZCmin right = "c"<br>		\|alt_msg=CHECK 3520 - Minimum U elevation must be higher than the minimum cell centre elevations on both sides in SGS. ZCmin left = "a", ZUmin = "b", ZCmin right = "c"<br>
	Minimum V elevation must be higher than the minimum cell centre elevations on both sides in SGS. ZCmin left = "a", ZUmin = "b", ZCmin right = "c"		CHECK 3520 - Minimum V elevation must be higher than the minimum cell centre elevations on both sides in SGS. ZCmin left = "a", ZUmin = "b", ZCmin right = "c"
	\|type=[[CHECK]]		\|type=[[CHECK]]
	\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.		\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.

ElizaCollison at 00:41, 16 December 2022

2022-12-16T00:41:53Z

← Older revision		Revision as of 10:41, 16 December 2022
Line 9:		Line 9:
	\|prelink=[[TUFLOW_Message_3519\|Message 3519]]		\|prelink=[[TUFLOW_Message_3519\|Message 3519]]
	\|uplink=[[3xxx_TUFLOW_Messages\|3xxx Messages]]		\|uplink=[[3xxx_TUFLOW_Messages\|3xxx Messages]]
	\|nextlink=[[~~TUFLOW_Message_3522~~\|Message ~~3522~~]]		\|nextlink=[[TUFLOW_Message_3521\|Message 3521]]
	}}		}}

Melissa.Moghanloo at 00:37, 18 July 2022

2022-07-18T00:37:49Z

← Older revision		Revision as of 10:37, 18 July 2022
Line 5:		Line 5:
	\|type=[[CHECK]]		\|type=[[CHECK]]
	\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.		\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.
	\|suggestions=Although TUFLOW automatically correct the face elevations, users can turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>ON</tt>" (the default is "<tt>OFF</tt>") to report every faces with the issue to the _message_p layer. If the geometries input layers are all correctly set around these faces, turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt>" to omit this warning message.		\|suggestions=Although TUFLOW automatically correct the face elevations, users can turn <font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>ON</tt> (the default is "<tt>OFF</tt>") to report every faces with the issue to the _message_p layer. If the geometries input layers are all correctly set around these faces, turn <font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt> to omit this warning message.

	\|prelink=[[TUFLOW_Message_3519\|Message 3519]]		\|prelink=[[TUFLOW_Message_3519\|Message 3519]]

Melissa.Moghanloo at 05:24, 13 July 2022

2022-07-13T05:24:22Z

← Older revision		Revision as of 15:24, 13 July 2022
Line 6:		Line 6:
	\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.		\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.
	\|suggestions=Although TUFLOW automatically correct the face elevations, users can turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>ON</tt>" (the default is "<tt>OFF</tt>") to report every faces with the issue to the _message_p layer. If the geometries input layers are all correctly set around these faces, turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt>" to omit this warning message.		\|suggestions=Although TUFLOW automatically correct the face elevations, users can turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>ON</tt>" (the default is "<tt>OFF</tt>") to report every faces with the issue to the _message_p layer. If the geometries input layers are all correctly set around these faces, turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt>" to omit this warning message.

	\|discussion_page=* [[Talk:TUFLOW Message 3520\|Discuss Message 3520]]
	\|link3=''
	\|link4=''
	\|prelink=[[TUFLOW_Message_3519\|Message 3519]]		\|prelink=[[TUFLOW_Message_3519\|Message 3519]]
	\|uplink=[[3xxx_TUFLOW_Messages\|3xxx Messages]]		\|uplink=[[3xxx_TUFLOW_Messages\|3xxx Messages]]

ShuangGao at 00:18, 15 July 2021

2021-07-15T00:18:48Z

← Older revision		Revision as of 10:18, 15 July 2021
Line 5:		Line 5:
	\|type=[[CHECK]]		\|type=[[CHECK]]
	\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.		\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.
	\|suggestions=~~Check~~ in ~~_message_p~~ ~~layer~~ ~~where~~ ~~this~~ is ~~happening~~ ~~and~~ ~~which~~ ~~Zpts~~ ~~command~~ is ~~causing~~ ~~this~~. If the input layers are all correctly set, turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt>" to omit this warning message.		\|suggestions=Although TUFLOW automatically correct the face elevations, users can turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>ON</tt>" (the default is "<tt>OFF</tt>") to report every faces with the issue to the _message_p layer. If the geometries input layers are all correctly set around these faces, turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt>" to omit this warning message.
	\|discussion_page=* [[Talk:TUFLOW Message 3520\|Discuss Message 3520]]		\|discussion_page=* [[Talk:TUFLOW Message 3520\|Discuss Message 3520]]
	\|link3=''		\|link3=''

ShuangGao at 23:24, 22 September 2020

2020-09-22T23:24:59Z

← Older revision		Revision as of 09:24, 23 September 2020
Line 5:		Line 5:
	\|type=[[CHECK]]		\|type=[[CHECK]]
	\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.		\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.
	\|suggestions=Check in _message_p layer where this is happening and which Zpts command is causing this. If the input layers are all correctly set, ~~you can also~~ turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt>" to omit this warning message.		\|suggestions=Check in _message_p layer where this is happening and which Zpts command is causing this. If the input layers are all correctly set, turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt>" to omit this warning message.
	\|discussion_page=* [[Talk:TUFLOW Message 3520\|Discuss Message 3520]]		\|discussion_page=* [[Talk:TUFLOW Message 3520\|Discuss Message 3520]]
	\|link3=''		\|link3=''

ShuangGao at 23:01, 22 September 2020

2020-09-22T23:01:48Z

← Older revision		Revision as of 09:01, 23 September 2020
Line 4:		Line 4:
	Minimum V elevation must be higher than the minimum cell centre elevations on both sides in SGS. ZCmin left = "a", ZUmin = "b", ZCmin right = "c"		Minimum V elevation must be higher than the minimum cell centre elevations on both sides in SGS. ZCmin left = "a", ZUmin = "b", ZCmin right = "c"
	\|type=[[CHECK]]		\|type=[[CHECK]]
	\|message_desc=SGS model ~~need~~ to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.		\|message_desc=SGS model needs to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.
	\|suggestions=Check in _message_p layer where this is happening and which Zpts command is causing this. If the input layers are all correctly set, you can also turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt>" to omit this warning message.		\|suggestions=Check in _message_p layer where this is happening and which Zpts command is causing this. If the input layers are all correctly set, you can also turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt>" to omit this warning message.
	\|discussion_page=* [[Talk:TUFLOW Message 3520\|Discuss Message 3520]]		\|discussion_page=* [[Talk:TUFLOW Message 3520\|Discuss Message 3520]]

ShuangGao at 23:01, 22 September 2020

2020-09-22T23:01:04Z

← Older revision		Revision as of 09:01, 23 September 2020
Line 1:		Line 1:
	{{TUFLOW_Message		{{TUFLOW_Message
	\|tuflow_message=CHECK 3520 - Found SGS cell face that has minimum Face elevation lower than the minimum cell centre elevations on both sides.		\|tuflow_message=CHECK 3520 - Found SGS cell face that has minimum Face elevation lower than the minimum cell centre elevations on both sides.
			\|alt_msg=Minimum U elevation must be higher than the minimum cell centre elevations on both sides in SGS. ZCmin left = "a", ZUmin = "b", ZCmin right = "c"<br>
	\|alt_msg=NA
			Minimum V elevation must be higher than the minimum cell centre elevations on both sides in SGS. ZCmin left = "a", ZUmin = "b", ZCmin right = "c"
	\|type=[[CHECK]]		\|type=[[CHECK]]
	\|message_desc=SGS ~~cell~~ ~~face~~ ~~has~~ ~~minimum~~ ~~Face~~ elevation lower than the minimum cell centre elevations on both sides.		\|message_desc=SGS model need to insure every cell face elevation is NOT lower than the minimum cell centre elevations on both sides. The warning suggest discontinuity in sub-grid elevation, which can happen occasionally during pre-processing of Sub-Grid Sampling. If this happens, the cell face elevation will be increased automatically to insure simulation stability.
			\|suggestions=Check in _message_p layer where this is happening and which Zpts command is causing this. If the input layers are all correctly set, you can also turn "<font color="blue"><tt>SGS Face Elevation Warning</tt></font> <font color="red"><tt>==</tt></font> <tt>OFF</tt>" to omit this warning message.
	\|suggestions=
	\|discussion_page=* [[Talk:TUFLOW Message 3520\|Discuss Message 3520]]		\|discussion_page=* [[Talk:TUFLOW Message 3520\|Discuss Message 3520]]
	\|link3=''		\|link3=''

Pavlina Monhartova: Created page with "{{TUFLOW_Message |tuflow_message=CHECK 3520 - Found SGS cell face that has minimum Face elevation lower than the minimum cell centre elevations on both sides. |alt_msg=NA |typ..."

2020-07-21T01:14:32Z

Created page with "{{TUFLOW_Message |tuflow_message=CHECK 3520 - Found SGS cell face that has minimum Face elevation lower than the minimum cell centre elevations on both sides. |alt_msg=NA |typ..."

New page

{{TUFLOW_Message
|tuflow_message=CHECK 3520 - Found SGS cell face that has minimum Face elevation lower than the minimum cell centre elevations on both sides.
|alt_msg=NA
|type=[[CHECK]]
|message_desc=SGS cell face has minimum Face elevation lower than the minimum cell centre elevations on both sides.
|suggestions=
|discussion_page=* [[Talk:TUFLOW Message 3520|Discuss Message 3520]]
|link3=''
|link4=''
|prelink=[[TUFLOW_Message_3519|Message 3519]]
|uplink=[[3xxx_TUFLOW_Messages|3xxx Messages]]
|nextlink=[[TUFLOW_Message_3522|Message 3522]]
}}