Difference between revisions of "TUFLOW Version Backward Compatibility"
Jump to navigation
Jump to search
Chris Huxley (talk | contribs) |
Chris Huxley (talk | contribs) |
||
Line 7: | Line 7: | ||
| rowspan=1|2016-03-AA | | rowspan=1|2016-03-AA | ||
− | | | + | | Numerous default updates: New operational 1D structure defaults. Primary upstream and downstream 1D channels now correctly takes into account bed slope. A new layered 2D FC calculation method has been implemented. The SX Flow Distribution Cutoff Depth has been raised to 0.05m from 0.00m. The End After Maximum tolerance has been increased to 0.001m from 0.0m. A new ERROR message has been added to cross-check the 1D timestep is a multiple of the timestep for all 2D domains. WARNING 2460 has been escalated to an ERROR and stricter command line syntax rules have been introduced ("=" will now return an ERROR message if TUFLOW is expecting "=="). |
− | | | + | | Set <font color="blue"><u>Defaults == PRE 2016</u></font> if similar results are required to the 2013-12-AC release. |
|- | |- | ||
| rowspan=1|2016-03-AC | | rowspan=1|2016-03-AC | ||
− | | | + | | No default value changes or enhancements in addition to 2016-03-AA. |
− | | | + | | Set <font color="blue"><u>Defaults == PRE 2016</u></font> if similar results are required to the 2013-12-AC release. |
|- | |- | ||
| rowspan=1|2016-03-AD | | rowspan=1|2016-03-AD | ||
− | | | + | | The treatment of the eddy viscosity term in the GPU Solver has been enhanced with slightly improved results in areas of rapidly changing velocity patterns. |
− | | | + | | Set <font color="blue"><u>GPU Viscosity Method == Method A</u></font> to achieve the same results as Build 2016-03-AC and prior. |
|- | |- | ||
Revision as of 17:37, 24 January 2017
2016-03-XX Builds | ||
2016-03-AA | Numerous default updates: New operational 1D structure defaults. Primary upstream and downstream 1D channels now correctly takes into account bed slope. A new layered 2D FC calculation method has been implemented. The SX Flow Distribution Cutoff Depth has been raised to 0.05m from 0.00m. The End After Maximum tolerance has been increased to 0.001m from 0.0m. A new ERROR message has been added to cross-check the 1D timestep is a multiple of the timestep for all 2D domains. WARNING 2460 has been escalated to an ERROR and stricter command line syntax rules have been introduced ("=" will now return an ERROR message if TUFLOW is expecting "=="). | Set Defaults == PRE 2016 if similar results are required to the 2013-12-AC release. |
2016-03-AC | No default value changes or enhancements in addition to 2016-03-AA. | Set Defaults == PRE 2016 if similar results are required to the 2013-12-AC release. |
2016-03-AD | The treatment of the eddy viscosity term in the GPU Solver has been enhanced with slightly improved results in areas of rapidly changing velocity patterns. | Set GPU Viscosity Method == Method A to achieve the same results as Build 2016-03-AC and prior. |
2013-12-XX Builds | ||
2013-12-AA | New default settings – see Defaults == PRE 2013-12 for a list of the commands that have changed in their default setting. | Set Defaults == PRE 2013-12 if similar results are required to the 2012-05 release. |
2013-12-AC | The default setting for Link 2D2D Approach has changed. | Set Link 2D2D Approach == METHOD B to achieve the same results as Builds 2013-12-AA and 2013-12-AB. See Link 2D2D Approach for more information. |
2011-09-XX and 2012-05-XX Builds | ||
2012-05-AA | New default settings – see Defaults == PRE 2012-05 for a list of the commands that have changed in their default setting. | Set Defaults == PRE 2012-05 if similar results are required to the 2011-09 or 2010-10 releases. |
The approach to the sizing of automatic manholes and the application of losses has been enhanced. | Set Manhole Approach == Method A to achieve the same results as Build 2011-09-AA. | |
2011-09-AA | The optimised compiler code is treated differently for Single Precision builds producing slightly different results (fractions of a mm) for some models. | No workaround. |
2010-10-XX Builds | ||
2010-10-AA | New Intel Fortran Compiler version produces slightly different results (usually fractions of a mm). | No workaround. |
w32 and w64 versions will give slightly different results for the same simulation. | No workaround. Use the same platform (w32 or w64) for all simulations. Use Model Platform to force which platform should be used. | |
New default settings – see Defaults == PRE 2010-10 for a list of the commands that have changed in their default setting. | Set Defaults == PRE 2010-10 if similar results are required to the 2008-08 or 2009 07 releases. | |
Generation of TINs for polygons in Read GIS Shape layers is more robust and uses an improved approach. In rare cases, the TIN would fail and TUFLOW would abort the start-up. | No workaround. | |
2008-08-XX and 2009-07-XX Builds | ||
2008-08-AC | The default setting for Shallow Depth Stability Factor has changed. | Set Shallow Depth Stability Factor == 3 for models without direct rainfall to achieve the same results as Builds 2008-08-AA and 2008-08-AB. See Shallow Depth Stability Factor for more information. |
2008-08-AA | ||
Uses a new set of defaults for a number of commands (see Defaults ). | The new defaults produce slightly different results, and very slight differences also occur between the three versions offered. For established models run using the 2007-07-XX builds, use Defaults == PRE 2008-08 to use the default settings used by the 2007-07-XX builds. Testing of a range of models has shown zero change in results if Defaults == PRE 2008-08 switch is set, and the Compaq Fortran compiled version (cSP) is used. Each of the new default settings and their effects are discussed in the rows below. | |
The method for interpolating n values where the 2D Manning’s n varies with depth has been enhanced from a linear interpolation of the M (1/n) value to a spline interpolation of the n value. See Bed Resistance Depth Interpolation. | Generally has little effect other than when the flow is predominantly in the depth range that the n value is varying. The new approach offers a smoother transition in n values from one depth to the other. | |
The default viscosity coefficient is now a combination of a 0.2 Smagorinsky and 0.1 constant coefficient, and there are some enhancements to the application of the viscosity term. See Viscosity Coefficient. | This has slight effect for the majority of models. For fine grid models (<2m cell size) with low bed resistance and significant variations in velocity vectors the effect is more pronounced but is still slight. | |
Inertia and viscosity terms are now not transferred across dry cell sides when constructing the coefficients for the solution arrays. This was having the effect of generating a circulation on the other side of the wall (albeit a very weak one), which of course shouldn’t happen! | Generally little effect, but can have some minor influence for urban models where buildings and fences are modelled as solid thin Z lines. | |
1D weir flow has been improved as the water level difference across the weir approaches zero. The new method is more stable. See Weir Flow. | Very little difference other than improved stability. | |
Incorporates minor improvements for transitioning between Regimes A and B, and between inlet and outlet controlled regimes, for circular culverts. | Very little difference other than improved stability. | |
The new automatic selection of cells for 2D SX connections using the 1d_nwk Conn_1D_2D attribute may choose more than one 2D cell. | Very little difference other than improved stability at the pit 2D connections. | |
2007-07-XX Builds | ||
2007-07-AA | ||
Uses a new set of defaults for a number of commands (see Defaults). | The new defaults may produce slightly different results. For established models run using the 2006-06-XX builds, use Defaults == PRE 2007-07-AA to use the default settings used by the 2006-06-XX builds. Testing of a range of models has shown zero change in results if Defaults == PRE 2007-07-AA switch is set. Each of the new default settings and their affects are discussed in the rows below. | |
Change Zero Material Values to One == OFF (previously ON) | Will not cause different results if a Set Mat == 1 is specified before other material settings in the .tgc file, or if every cell has been assigned a material value. | |
Inside Region == Method B (previously Method A) | Testing thus far has not shown any difference between the two methods (other than the substantial gains in processing time of polygons). | |
Line Cell Selection == Method D (previously Method C) | May change results slightly, but improved stability and a smoother water levels along HX lines result. | |
VG Z Adjustment == MAX ZC (previously ZC) | May change results slightly, but stability should be significantly enhanced in some situations. | |
Bed Resistance Cell Sides == INTERROGATE (previously AVERAGE M) | Will influence results, usually slightly, but more pronounced where there are sudden changes in Manning’s n values such as in the urban environment. | |
Culvert Flow == Method D (previously Method C)
Culvert Critical H/D == OFF (previously Culvert Critical H/D == 1.5) |
The most significant influences are the selection of upstream or downstream controlled regimes depending on the H/D ratio, and the bug fix relating to Regime E if Structure Losses == ADJUST. Offers improved stability, better convergence for Regime C and smoother transitioning between some regimes. | |
Changed the setting of the default width (if eN1 < 0.001) of automatic weirs over R and C channels (i.e. RW and CW) to be the diameter/width multiplied by the number of culverts (previously, the width was not multiplied by the number of culverts). | For backward compatibility, original weir width can be set by manually setting the eN1 attribute to the Diameter_or_Width attribute value of the culvert. | |
Bug fix that when using a restart file TUFLOW occasionally set the 2D FC bridge deck additional loss value incorrectly. | No backward compatible workaround provided. | |
Bug fix that incorrectly set the water levels on dried VG cells (only applies to simulations with source inflows, e.g. SA or RF, somewhere within in the model). | May cause slight changes in results. Backward compatibility provided if Defaults == PRE 2007-07-AA is set (noting that setting this command reinstates the bug). This bug also causes the mass error calculations to falsely give a mass error that is not occurring. | |
Fixed bug that did not correctly apply the reduction in conveyance for a FC BD (bridge deck) of FD (floating deck) cell using the 2d_fc Mannings_n attribute. | Backward compatibility applied if Defaults == PRE 2007-07-AA is set, however, note that this reinstates the bug and the resistance to flow at FC BD and FD cells may need to be reviewed. Indications are that only minor changes in results occur. The flow area under 2D FC BD and FD cells is correctly calculated. | |
2006-06-XX Builds | ||
2006-06-AA | ||
Uses a new set of defaults for a number of commands. | The new defaults will produce different results. For established models run using the 2005-05-XX builds, use Defaults == PRE 2006-06-AA to use the previous default settings. Each of the new default settings and their affects are discussed in the rows below. | |
Cell Wet/Dry Depth == 0.002 previously 0.05) and Cell Side Wet/Dry Depth == 0.001 (previously 0.03) | The most pronounced effect of the shallower wet/dry depths is likely to occur in areas that are still filling at the flood peak, such as behind a levee that is only just overtopped. The shallower wet/dry depths provides a greater flow depth for a longer period over the levee. | |
Adjust Head at ESTRY Interface == OFF (previously ON) | Usually does not have a major influence on results except where very high velocities occur. | |
Boundary Cell Selection == Method C (previously Method A) and Line Cell Selection == Method C (previously Method A) | May select slightly different cells along boundary/link lines. This may cause a difference where the line is along the top of levee, possibly creating a “hole” in embankment. | |
Viscosity Formulation == Smagorinsky (previously Constant) and Viscosity Coefficient == 0.2 (previously 1.0) | Can have a significant effect where the viscosity term is influential. This occurs where the friction term is less dominant (i.e. low Manning’s n and/or deeper water such as the lower, tidal, reaches of rivers). | |
Structure Losses == ADJUST (previously FIX) | Can have a significant affect in the vicinity of structures within a 1D network and for culvert networks. Does not affect 1D structures linked to a 2D domain or at the structure ends not connected to another 1D channel. | |
Storage Above Structure Obvert (%) == 5 (previously CHANNEL WIDTH) | Usually negligible effect unless the model storage is predominantly within 1D closed sections (i.e. B, C and R channels). The 1D domain is likely to be more sensitive to instabilities due to the much smaller storage above the top of the closed sections, therefore, a smaller 1D timestep may be required and/or the Storage Above Structure Obvert (%) increased. | |
Depth Limit Factor == 10 (previously 1) | No effect as previously the model would have become “unstable” as the trigger for an instability was the top of the channel/node. | |
Culvert Flow == Method C (previously Method B) | Usually only minor effects plus improved stability. | |
Culvert Add Dynamic Head == ON (previously OFF) | Minor influence. | |
Bridge Flow == Method B (previously Method A) | Negligible influence plus improved stability. However, note the different treatment of energy losses once the bridge deck obvert/soffit is submerged if a BG or LC table is specified. | |
WLL Approach == Method B (previously Method A) | Only affects the presentation of results. Note, that Method A is no longer recommended or supported. | |
Apply All Inverts == ON (previously OFF)
Does not affect hydraulic calculations, however, if a Blank, B or W channel is now lowered/raised because the inverts are now used, this will affect results/stability - see note at end of Apply All Inverts). | ||
Conveyance Calculation == ALL PARALLEL (previously CHANGE IN RESISTANCE) | Will affect results as ALL PARALLEL can be around 10% more “slippery” than CHANGE IN RESISTANCE. For calibrated or established models developed using build prior to Build 2006-06-AA , recommend setting to CHANGE IN RESISTANCE | |
Flow Calculation == Method B (previously Method A) | Negligible effect. | |
Builds prior to 2006-06-XX | Contact support@tuflow.com |
Up |
---|
![]() |