1D Weirs: Difference between revisions

Content deleted Content added
Rohan.king (talk | contribs)
No edit summary
 
(5 intermediate revisions by 3 users not shown)
Line 1:
<font size = 18>Page Under Construction</font>
<br>
<br>
<br>
=Introduction=
A weir is a barrier across a designated flow path that is designed to alter flow characteristics. Most common weirs act as an obstruction, smaller but similar to a dam, that pools water behind it while allowing water to steadily flow over the top. Weirs within TUFLOW, like bridges, do not require data for length, Manning's n, divergence or bed slope so they are zero-length channels effectively.
Line 8 ⟶ 4:
 
==Weir types that can be used within TUFLOW==
*''under construction''
<br>
;Broad-crested weir
Broad Crested weirs are commonly used to measure the discharge of large rivers and canals.
 
[[File:Broad-crested weir.jpg|thumb|none|400px|https://i.ytimg.com/vi/SNYqKkjHacE/maxresdefault.jpg]]
 
<br>
;Crump weir
The Crump Weir models a triangular profile weir with a 1:2 sloping front face and a 1:5 sloping back face. This type of weir are used as measuring structures within open channel.
Line 21 ⟶ 14:
[[File:Crump_weir - lamprey-barrier.jpg|thumb|none|400px|https://ecofactireland.files.wordpress.com/2014/04/lamprey-barrier.jpg]]
 
<br>
;Ogee-crested weir
An ogee-crested weir is a special type of weir, generally used as a spillway of a dam as shown in figure. The crest of an ogee weir slightly rises up from the inside edge (i.e., a slight hump on top of the weir) and falls in a parabolic form over the edge of the weir.
Line 27 ⟶ 19:
[[File:Ogee-crested weir.jpg|thumb|none|400px|http://www.ancold.org.au/wp-content/uploads/2014/08/Figure-2Harvey-Dam-Ogee-crest-over-flowing-for-the-first-time.jpg]]
 
<br>
;Rectangular weir (sharp crested)
Sharp crested weirs are used to measure discharge in small rivers and canals.
 
 
<br>
;Trapezoidal or Cippoletti weir
The "Cippoletti" weir is a trapezoidal shaped weir. The purpose of the slope, on the sides, is to obtain an increased discharge through the triangular portions of the weir, which otherwise would have been decreased due to end contractions in the case of rectangular weirs.
Line 43 ⟶ 32:
[[File:V-notch weir.jpg|thumb|none|400px|http://wintertracadie.ca/wp-content/uploads/2013/12/V-notch-weir-to-measure-spring-flow.jpg]]
 
<br>
;Spillway
 
<br><br><br><br><br><br><br>
[[File:Weir_in_Bath_UK.jpg|border|400px]]
<br>
Bath, UK (pht: Rohan King)
 
Any further questions please email TUFLOW support: [mailto:support@tuflow.com?Subject=TUFLOW%201D%20weirs%20help support@tuflow.com]
<br>
 
==Irregular shaped weirs==
*''under construction''
 
=Operational Control=
*''under construction''
 
=Typical check files used=
*''under construction''
<br>
<br>
Any further questions please email TUFLOW support: [mailto:support@tuflow.com support@tuflow.com]
<br><br>
{{Tips Navigation
Back to [[TUFLOW_1D_Hydraulic_Structures | 1D Hydraulic Structures]]
|uplink=[[ TUFLOW 1D Channels and Hydraulic Structures | Back to 1D Channels and Hydraulic Structures]]
}}