MIKE Flood to TUFLOW

This page is currently under construction

Introduction

This page provides guidance on a generalised method to convert a MIKE FLOOD model to a TUFLOW model format. MIKE Flood is the top level program that couples MIKE21 (the MIKE 2D engine and program) with MIKE11 (the MIKE 1D engine and program). These programs are referenced when converting the relevant setup to TUFLOW format. These steps could therefore also be used for converting stand-alone MIKE21 or MIKE11 models to TUFLOW format.

If you have any suggestions to be included in these pages, please email support@tuflow.com.

Requirements

The following programs are required in the conversion process:

• MIKE Zero
• xsGenerator.exe (for MIKE11 conversion)

MIKE Zero is required to extract data from the MIKE FLOOD model. The tools required are freely available using the Demo version of Mike Zero.
For MIKE11 conversion, the xsGenerator utility has been made to automate some of the steps. The xsGenerator utility is freely available from the TUFLOW website.

Creating a TUFLOW Geometry Control File from MIKE21

This section discusses how to extract data from a MIKE model to populate the TUFLOW Geometry Control file (TGC). The TGC file defines the:

• Terrain elevation
• Manning's values
• Model domain
• Active cells

To

Converting Terrain

Like TUFLOW, MIKE uses a grid file to define the underlying terrain. MIKE uses its own grid format (.dsf2) as well as a local coordinate system. For these reasons, it needs to be converted into a format that TUFLOW can read as well as an absolute coordinate system.
The terrain .dfs2 grid can be converted through the MIKE Zero toolbox. This can be done through the following steps:

1. Open the MIKE Zero program
2. From the MIKE Zero shell select File >> New >> File
   
3. On the MIKE Zero button select MIKE Zero Toolbox (.mzt). Click OK.
   
4. Under the GIS dropdown, double click MIKE2GRD
   
5. Work through the steps being careful to specify an appropriate projection
6. Before clicking Finish, ensure you have clicked Execute to run the conversion
   
7. This should produce an ascii file that can be directly read by TUFLOW

Unlike TUFLOW, the grid cell size of the model in MIKE is determined directly by the input grid file. For more discussion on grid cell size and the differences in how MIKE and TUFLOW handle the underlying terrain please see the discussion section at the bottom of the page.

Note: After grid conversion, it is important to perform checks that the ascii grid has converted properly. This is best done in your preferred GIS package.

Converting Manning's

Follow the same steps as converting terrain to convert the manning’s grid using the Mike Zero Toolbox. It is important to identify the manning’s value type (M or n) so that it can be correctly read into TUFLOW. This can be done by viewing the .dfs2 grid in Mike Zero following the steps below:

1. Open the MIKE Zero program
2. Open the .dfs2 file through Open (or drag and drop)
3. From the toolbar select Edit >> Items…
4. The value should be listed in Type
   

More information on reading in manning’s grids into TUFLOW is provided in Section 6.9 of the TUFLOW Manual.

Model Domain

The model domain can be manually set by viewing the terrain and manning’s data in your preferred GIS program, or set using the Read Grid Location command.

! Set model domain
Read Grid Location == ..\model\grid\example_grid.asc

More information on setting the model domain is provided in Section 6.5 of the TUFLOW Manual.

TUFLOW Code Layer

The user can manually set the TUFLOW code layer by viewing the terrain data through their preferred GIS program or, it should be noted, that MIKE uses a process of defining active cells by defining a ‘Land’ elevation value. A ‘Land’ elevation value is specified in the .dsf2 grid file that specifies a value at which elevations equal to or greater than this value are considered ‘Land’ and will not be subject to possible wetting and drying. This value could be used as a guidance for producing a TUFLOW code layer. The steps in identifying this value are as follows:

1. Open the MIKE Zero program
2. Open the .dfs2 elevation grid through Open (or drag and drop)
3. From the toolbar select Edit >> Custom Blocks…
4. The fourth element value is the ‘Land’ value elevation
   

Note: A downfall of this method in MIKE, is that elevations in the .dfs2 grid could have been manually modified such that the area outside the flood extent has a constant ‘Land’ elevation. Inspection of the terrain data before use is highly recommended.