Difference between revisions of "TUFLOW 2D Cell Size Selection"
Jump to navigation
Jump to search
Chris Huxley (talk | contribs) |
Chris Huxley (talk | contribs) |
||
| Line 21: | Line 21: | ||
| '''Cell Size''' || '''Location 4 Result'''|| '''Location 5 Result''' || '''Mesh Resolution Figure''' | | '''Cell Size''' || '''Location 4 Result'''|| '''Location 5 Result''' || '''Mesh Resolution Figure''' | ||
|- | |- | ||
| − | | 10m || [[File:Mesh Converge Exg P4 010.png|400px]] || [[File:Mesh Converge Exg P5 010.png|400px]] ||[[File: | + | | 10m || [[File:Mesh Converge Exg P4 010.png|400px]] || [[File:Mesh Converge Exg P5 010.png|400px]] ||[[File:Mesh Converge Grid 010.png|500px]] |
|- | |- | ||
| − | | 20m || [[File:Mesh Converge Exg P4 020.png|400px]] || [[File:Mesh Converge Exg P5 020.png|400px]] || [[File:Mesh_Converge_Grid_020.png| | + | | 20m || [[File:Mesh Converge Exg P4 020.png|400px]] || [[File:Mesh Converge Exg P5 020.png|400px]] || [[File:Mesh_Converge_Grid_020.png|500px]] |
|- | |- | ||
| − | | 50m || [[File:Mesh Converge Exg P4 050.png|400px]] || [[File:Mesh Converge Exg P5 050.png|400px]] ||[[File:Mesh_Converge_Grid_050.png| | + | | 50m || [[File:Mesh Converge Exg P4 050.png|400px]] || [[File:Mesh Converge Exg P5 050.png|400px]] ||[[File:Mesh_Converge_Grid_050.png|500px]] |
|- | |- | ||
| − | | 100m || [[File:Mesh Converge Exg P4 100.png|400px]]|| [[File:Mesh Converge Exg P5 100.png|400px]] || [[File:Mesh_Converge_Grid_100.png| | + | | 100m || [[File:Mesh Converge Exg P4 100.png|400px]]|| [[File:Mesh Converge Exg P5 100.png|400px]] || [[File:Mesh_Converge_Grid_100.png|500px]] |
|- | |- | ||
| − | | 150m || [[File:Mesh Converge Exg P4 150.png|400px]] || [[File:Mesh Converge Exg P5 150.png|400px]] ||[[File:Mesh_Converge_Grid_150.png| | + | | 150m || [[File:Mesh Converge Exg P4 150.png|400px]] || [[File:Mesh Converge Exg P5 150.png|400px]] ||[[File:Mesh_Converge_Grid_150.png|500px]] |
|- | |- | ||
| − | | 200m || [[File:Mesh Converge Exg P4 200.png|400px]] || [[File:Mesh Converge Exg P5 200.png|400px]] ||[[File:Mesh_Converge_Grid_200.png| | + | | 200m || [[File:Mesh Converge Exg P4 200.png|400px]] || [[File:Mesh Converge Exg P5 200.png|400px]] ||[[File:Mesh_Converge_Grid_200.png|500px]] |
|- | |- | ||
| − | | 250m || [[File:Mesh Converge Exg P4 250.png|400px]] || [[File:Mesh Converge Exg P5 250.png|400px]] ||[[File:Mesh_Converge_Grid_250.png| | + | | 250m || [[File:Mesh Converge Exg P4 250.png|400px]] || [[File:Mesh Converge Exg P5 250.png|400px]] ||[[File:Mesh_Converge_Grid_250.png|500px]] |
|} | |} | ||
| + | |||
==Rural Assessment Result Discussion== | ==Rural Assessment Result Discussion== | ||
Revision as of 12:45, 14 August 2018
This page is currently under construction.
Introduction
Cell size convergence is an important concept in flood modelling.... why?
Rural Catchment Scenario Assessment
Rural Model Description
This test is designed to simulate flood wave propagation down a river valley following the failure of a dam. The valley DEM is ~0.8 km by ~17 km and the valley slopes downstream on a slope of ~0.01 in its upper region, easing to ~0.001 at lower elevations.
The inflow hydrograph shown below is applied as a boundary condition at the upstream end of the valley.
Rural Assessment Results
| Cell Size | Location 4 Result | Location 5 Result | Mesh Resolution Figure |
| 10m |  |
 |
|
| 20m |  |
 |
|
| 50m |  |
 |
|
| 100m |  |
 |
|
| 150m |  |
 |
|
| 200m |  |
 |
|
| 250m |  |
 |
|