Difference between revisions of "TUFLOW HR Output"

From Tuflow
Jump to navigation Jump to search
Line 7: Line 7:
 
For the HR output the water level at each HR output location is interpolated from the computed 2D water levels. The depth is the difference between the interpolated water level and the sub-grid elevation. This differs from the standard depth output which calculates the depths at cell centres and corners first, then interpolate the depths to the standard output grid locations(default is half the cell size). The difference in the interpolation process is illustrated below.
 
For the HR output the water level at each HR output location is interpolated from the computed 2D water levels. The depth is the difference between the interpolated water level and the sub-grid elevation. This differs from the standard depth output which calculates the depths at cell centres and corners first, then interpolate the depths to the standard output grid locations(default is half the cell size). The difference in the interpolation process is illustrated below.
  
[[File:Sgs_std_output.png|400px]] [[File:Sgs_hr_output.png|400px]]
+
[[File:Sgs_std_output.png|360px]] [[File:Sgs_hr_output.png|360px]]
  
 
The advantage of the HR output is that it can retain the sub-grid detail of the terrain information even at coarse cell size. As compared in the example below, the HR depth output shows clear flow path even at 100m grid. However, nicer depth output does not mean reliable hydraulic result. In fact, the 100m cell size is too coarse to produce reliable/converged hydraulic results for any real-world flood model. It's is strongly recommended that the model convergence/benchmarking tests must be conducted based on the standard map output, and the HR output should be used for presentation purpose only.
 
The advantage of the HR output is that it can retain the sub-grid detail of the terrain information even at coarse cell size. As compared in the example below, the HR depth output shows clear flow path even at 100m grid. However, nicer depth output does not mean reliable hydraulic result. In fact, the 100m cell size is too coarse to produce reliable/converged hydraulic results for any real-world flood model. It's is strongly recommended that the model convergence/benchmarking tests must be conducted based on the standard map output, and the HR output should be used for presentation purpose only.
  
[[File:Sgs_std_vs_hr_output.png|800px]]
+
[[File:Sgs_std_vs_hr_output.png|720px]]
  
 
=Enable High Resolution Output=
 
=Enable High Resolution Output=

Revision as of 11:51, 20 February 2024

Page Under Construction


Introduction

High Resolution (HR) Grid/Raster Map Outputs was first introduced in TUFLOW 2020-10-AB release. When an SGS model uses “SGS Approach == Method C”, the sampled elevations are retained at the end of the geometry processing. These sub-grid elevations include topography modifiers such as breaklines, and they allow a high-resolution elevation check file to be written and used for high resolution depth map outputs. Currently, ASC, FLT and TIF raster formats are supported.

For the HR output the water level at each HR output location is interpolated from the computed 2D water levels. The depth is the difference between the interpolated water level and the sub-grid elevation. This differs from the standard depth output which calculates the depths at cell centres and corners first, then interpolate the depths to the standard output grid locations(default is half the cell size). The difference in the interpolation process is illustrated below.

Sgs std output.png Sgs hr output.png

The advantage of the HR output is that it can retain the sub-grid detail of the terrain information even at coarse cell size. As compared in the example below, the HR depth output shows clear flow path even at 100m grid. However, nicer depth output does not mean reliable hydraulic result. In fact, the 100m cell size is too coarse to produce reliable/converged hydraulic results for any real-world flood model. It's is strongly recommended that the model convergence/benchmarking tests must be conducted based on the standard map output, and the HR output should be used for presentation purpose only.

Sgs std vs hr output.png

Enable High Resolution Output

To produce high-resolution output, add “HRASC”, “HRFLT” or “HRTIF” to the “Map Output Format ==” command, for example:

Map Output Format == XMDF TIF HRTIF

At the moment, only water level and depth are supported as the High Resolution Output formats, i.e.:

HRTIF Map Output Data Types == h d

The map output data types and output interval can be defined separately for the High Resolution Output formats. For example:

Map Output Interval == 600 ! Sets all map output interval to 600 seconds

HRTIF Map Output Interval == 3600 ! Sets HR map output interval to 3600 seconds

The output resolution for high resolution grid output is defined using the following .tcf command:

HR Grid Output Cell Size == 0.5 ! m or ft

If this command is omitted, the default output resolution is set as the SGS sampling distance.

Water Level/Depth Interpolation Method

interpolated from the surrounding SGS sampled elevations.

  • under construction

Interpolation near Thin Breakline

  • under construction

Interpolation for Sheet Flow

  • under construction


Any further questions please email TUFLOW support: support@tuflow.com


Up
Go-up.png Back to 1D Channels and Hydraulic Structures