Flood Modeller Tutorial Module01 Provisional: Difference between revisions

#Read in the GIS layers of the Flood Modeller Nodes. Place the below command line anywhere in the .tcf. It is good practice to create a section within the .tcf to reference all 1D commands:<br><u>'''QGIS - SHP'''</u><br><font color="blue"><tt>Read GIS X1D Nodes</tt></font> <font color="red"><tt>== </tt></font>..\model\gis\1d_x1d_FMT_M01_nodes_001_P.shp <font color="green"><tt>! GIS layer referencing node IDs from Flood Modeller </tt></font><br><u>'''QGIS - GPKG'''</u><br><font color="blue"><tt>Read GIS X1D Nodes</tt></font> <font color="red"><tt>== </tt></font> 1d_x1d_FMT_M01_nodes_001_P <font color="green"><tt>! GIS layer referencing node IDs from Flood Modeller</tt></font>

#Add commands to read in the GIS layers referencing Water Level Lines drawn along the Flood Modeller component of the model:<br><u>'''QGIS - SHP'''</u><br><font color="blue"><tt>Read GIS X1D Network</tt></font> <font color="red"><tt>== </tt></font>..\model\gis\1d_x1d_FMT_M01_nwk_001_L.shp <font color="green"><tt>! GIS layer representing channels to allow for the digitisation of Water Level Lines (optional)</tt></font><br><font color="blue"><tt>Read GIS X1D WLL</tt></font> <font color="red"><tt>== </tt></font> ..\model\gis\1d_x1d_WLL_FMT_M01_001_L.shp <font color="green"><tt>! GIS layer containing WLLs for visualising 1D results in 2D (optional)</tt></font><br><u>'''QGIS - GPKG'''</u><br><font color="blue"><tt>Read GIS X1D Network</tt></font> <font color="red"><tt>== </tt></font> 1d_x1d_FMT_M01_nwk_001_L <font color="green"><tt>! GIS layer representing channels to allow for the digitisation of Water Level Lines (optional)</tt></font><br><font color="blue"><tt>Read GIS X1D WLL</tt></font> <font color="red"><tt>== </tt></font> 1d_x1d_WLL_FMT_M01_001_L <font color="green"><tt>! GIS layer containing WLLs for visualising 1D results in 2D (optional)</tt></font><br>The addition of TUFLOW Water Level Lines (WLL) allows the Flood Modeller 1D results to be visualised within the TUFLOW 2D map outputs. They provide a means by which to remove the gaps in the map outputs where the 1D Flood Modeller domains are located and the 2D cells are deactivated. To do this, TUFLOW requires a 1D_WLL layer to define the cross sections locations, and a 1d_nwk layer that defines the river centre line. The layers are not used in the hydraulic calculations and their inclusion is not always required. The Dist_for_Add_Points determines the intervals in metres at which interpolation points are inserted along each WLL.

#Add commands to read in an ESTRY Control File which contains references to some of the culverts present on the floodplain:<br><font color="blue"><tt>ESTRY Control File</tt></font> <font color="red"><tt>== </tt></font>..\model\FMT_M01_001.ecf <font color="green"><tt>!Reference the ESTRY Control File </tt></font>

#Update the links to the Geometry control file, the Boundary Condition control file and the bc_dbase file:<br><font color="blue"><tt>Geometry Control File</tt></font> <font color="red"><tt>== </tt></font>..\model\FMT_M01_001.tgc <br><font color="blue"><tt>BC Control File</tt></font> <font color="red"><tt>== </tt></font>..\model\FMT_M01_001.tbc <br><font color="blue"><tt>BC Database</tt></font> <font color="red"><tt>== </tt></font>..\bc_dbase\bc_dbase_FMT_M01.csv