QGIS SWMM Junctions Set Attributes

From Tuflow
Jump to navigation Jump to search

Introduction

This tool sets SWMM junction attributes 'Ymax' (maximum depth), 'Ysur' (maximum surcharge depth), and 'Apond' (area of ponding). The junction attributes are set based on generic rules and individual nodes may need to be modified.
This tool supports in-place editing if selected in the QGIS processing window.

Usage

This tool, Junctions - Set Attributes, can be found in the QGIS processing toolbox panel under TUFLOW >> SWMM. To open the Processing Toolbox panel, navigate to 'Processing' in the menubar and select 'Toolbox'.

Open processing toolbox.png

Parameters

  1. Input layer: The junctions layer that will be updated.
  2. Selected features only: If nodes(s) in the junctions layer have been selected using the 'Select Features' tool, this option will become available. If this is checked on, the tool will only update the node(s) that have been selected.
  3. Input Subcatchments [optional]: The subcatchments layer(s) that the node(s) receive flow from.
  4. Input Inlet Usage Layers [optional]: The input inlet usage layer(s) that the node(s) are connected to.
  5. Input BC Connection Layers [optional]: The BC connection layer(s) that connect the node(s) to the 2D domain.
  6. For information on the other input parameters, refer to the Recommended Settings section.
  7. JunctionAtts: Determines the location and filename of the output junctions layer.

Note: If 'Edit Feature In-Place' is selected, the tool does not require the 'Input layer' or the 'JunctionAtts' parameters as the tool will override the existing junctions file with the updated attributes.

Junctions Set Attributes Dialog b.png

Recommended Settings

The recommended settings for junctions within the 2D domain depends on whether the node receives flow from a subcatchment and whether and how the node is connected to the 2D domain. Below is a description of the input parameters and their recommended values.

  1. General Options:
    • Maximum Depth Option (Ymax):
    • Set to 0.0: Initializes the Ymax for all junction nodes to 0.0. This option may be overwritten for nodes connected to inlets.
    • Leave as is: Leaves the Ymax value as is for all junction nodes. This option applies for 'Edit Feature In-Place' only.
    • Nodes receiving subcatchment flows option (if connected to 2D):
    • Based on options selected below: Options set below are applied.
    • Set Apond = 0.0; Ysur = 0.0 (overwrites options below): Forces subcatchment outlets to yse 0.0 for Ysur and Apond (turns off ponding). When ponding is off, node surcharging is reported as 'flooding' to SWMM and is immediately transferred to the 2D domain.
  2. Nodes connected to the 2D without inlets (through embankment culvert):
    • Ysur: 0.0
    • Apond: Approximate area of connected 2D cells. A larger area may improve stability, but may artificially attenuate discharges.
  3. Nodes connected to 2D with inlets (underground pipe network):
    • Maximum depth (Ymax) option (overwrites general setting):
    • Set to inlet elevation - node elevation: Sets the Ymax value to the inlet elevation minus the node elevation.
    • Use global option: Sets the Ymax value based on the settings selected in the 'Global Options' section.
    • Ysur: Set to 0.0 if using ponding. Otherwise, set to higher than expected depths to prevent flooding.
    • Area of ponding: Set to the manhole area.
  4. Nodes without a 2D connection (underground pipe network): When a node is not connected to the 2D, flood losses will be lost from the model resulting in mass losses and inaccurate results. To prevent this, allow ponding (option 1) or make the surcharge depth high (option 2).
    • Option 1:
    • Surcharge depth: Set to 0.0.
    • Area of ponding: Set to some positive value.
    • Option 2:
    • Surcharge depth: Set to a value higher than expected node depths.
    • Area of ponding: Set to 0.0.

Example



Using the 'Edit Feature In-Place' tool:


Up
Go-up.png Back to TUFLOW QGIS Plugin Main Page