Revision as of 23:13, 26 October 2016 view source Andrew.Sims (talk \| contribs) 155 edits →TCF File ← Older edit		Revision as of 23:36, 26 October 2016 view source Andrew.Sims (talk \| contribs) 155 edits →TCF File Newer edit →
Line 61: <li> The simulation time control commands (shown below) which specify timestep, start time and end time need to be removed from the tcf. and moved to an IEF file <br> <font color="green"><tt>! SIMULATION TIME CONTROL COMMANDS </tt></font> :<font color="blue"><tt>Timestep </tt></font> <font color="red"><tt>== </tt></font> 1.5 <font color="green"><tt>! Specifies a 2D computational timestep of 1.5 seconds </tt></font> :<font color="blue"><tt>Start time </tt></font> <font color="red"><tt>== </tt></font> 0 <font color="green"><tt>! Specifies a simulation start time of 0 hours </tt></font> :<font color="blue"><tt>End Time </tt></font> <font color="red"><tt>== </tt></font>3 <font color="green"><tt>! Specifies a simulation end time of 3 hours </tt></font> </li> ~~The reason for this step being completed is the information is to be moved to an IEF file </li>~~ <li> Delete the 1D Domain commands (shown below) from the tcf. These ~~are~~commands ~~shown~~should ~~below:~~be moved to the ecf. This an optional step. <br> :<font color="green"><tt>!1D DOMAIN COMMANDS </tt></font> :<font color="blue"><tt>Start 1D Domain </tt></font> <font color="green"><tt>! Indicates the start of a block of 1D or ecf (Estry Control File) commands </tt></font> <br> :<font color="blue"><tt>Output Folder </tt></font> <font color="red"><tt>== </tt></font> ..\results\M02\1d <font color="green"><tt>! Specifies the location of the 1D output files </tt></font> :<font color="blue"><tt>Write Check Files </tt></font> <font color="red"><tt>== </tt></font> ..\check\1d\ <font color="green"><tt>! Specifies the location of the 1D check files and prefixes them with the .tcf filename </tt></font> :<font color="blue"><tt>Output Interval (s) </tt></font> <font color="red"><tt>== </tt></font> 180 <font color="green"><tt>! Writes the 1D output every 3 minutes. Note the (s) is required to indicate the value is in seconds </tt></font> :<font color="blue"><tt>Timestep </tt></font> <font color="red"><tt>== </tt></font> 0.75 <font color="green"><tt>! Specifies a 1D computational timestep of 0.75 seconds. We will set the 1D timestep to be half the 2D timestep</tt></font> :<font color="blue"><tt>Read GIS Network </tt></font> <font color="red"><tt>== </tt></font> ..\model\gis\1d_nwk_M02_culverts_001_L.shp <font color="green"><tt>! Reads the 1d_nwk GIS layer defining culverts within the model</tt></font> :<font color="blue"><tt>Read GIS Network</tt></font> <font color="red"><tt>== </tt></font>..\model\gis\1d_nwk_M02_culverts_001_P.shp <font color="green"><tt>! Reads the 1d_nwk GIS layer defining nodes used to create automatic SX 1D/2D boundaries</tt></font> <font color="blue"><tt>End 1D Domain</tt></font> </li> <li> Flood modeller commands need to be added, these are: <br> :<font color="blue"><tt>Read GIS X1D Nodes</tt></font> <font color="red"><tt>== </tt></font>..\model\gis\1d_x1d_FMT_M01_nodes_001_p.shp <font color="green"><tt>! GIS layer referencing node IDs from Flood Modeller </tt></font> :<font color="blue"><tt>Read GIS X1D Network</tt></font> <font color="red"><tt>== </tt></font>..\model\gis\1d_x1d_FMT_M01_nwk_001_L.shp <font color="green"><tt>! GIS layer representing channels to allow for the digitisation of Water Level Lines (optional)</tt></font> ~~These commands should be moved to the ecf. This is however an optional step </li>~~ :<font color="blue"><tt>Read GIS X1D WLL</tt></font> <font color="red"><tt>== </tt></font> ..\model\gis\1d_x1d_WLL_FMT_M01_001_p.shp <font color="green"><tt>! GIS layer containing WLLs for visualising 1D results in 2D</tt></font> ==TGC File==

Flood Modeller Tutorial Module01: Difference between revisions